Command No. |
|
|
|
|
|
|
|
|
|
|
| Command Description |
|
| ||||
|
| [Active time (us) for the strobe signal] |
|
|
|
|
|
|
| |||||||||
90H: |
| Initial data: STROBEON _I[23..0] =10, STROBEDELAY _F[7..0] = 0, data range: 0 to 2,000,000 | ||||||||||||||||
STROBEON_I[7..0] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
91H: |
| Active time for the strobe signal = (STROBEON _I[23..0]). (STROBEON _F[7..0]) useconds | ||||||||||||||||
STROBEON_I[15..8] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
92H: | Active time for the strobe signal is set as below. |
|
|
|
|
| ||||||||||||
STROBEON_I[23..16] |
| 0: No strobe signal output |
|
|
|
|
|
|
|
|
|
| ||||||
93H: |
| 1 to 9: 10 us |
|
|
|
|
|
|
|
|
|
|
|
| ||||
STROBEON_F[7..0] |
| Greater than 9: set value |
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
| [Output signal selection for the | ||||||||||||||||
F0H: |
| Sets the output signal from the power/IO connector. |
|
|
| |||||||||||||
OUTSEL |
| D[7..0] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
[7..0] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| D7 | D6 | D5 |
| D4 |
| D3 |
| D2 | D1 |
| D0 |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| D7 to D4: | Output signal for 3pin of the power/IO connector |
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
| 0: FrameTriggerWait signal | 1: UserOutput signal | |||||||
|
|
|
|
|
|
|
|
|
| 2: ExposureActive signal | 3: TriggerAuxiliary signal | |||||||
|
|
|
|
|
|
|
|
|
| 4: TriggerInternal signal (after mask and delay process) | ||||||||
|
|
|
|
|
|
|
|
|
| 5: SensorReadOut signal |
|
|
| |||||
|
|
|
|
|
|
|
|
|
| 6 to F: No Function (Prohibited setting. Do not set these values) | ||||||||
|
| D3 to D0: | Output signal for 2pin of the power/IO connector |
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
| 0: FrameTriggerWait signal | 1: UserOutput signal | |||||||
|
|
|
|
|
|
|
|
|
| 2: ExposureActive signal | 3: TriggerAuxiliary signal | |||||||
|
|
|
|
|
|
|
|
|
| 4: TriggerInternal signal (after mask and delay process) | ||||||||
|
|
|
|
|
|
|
|
|
| 5: SensorReadOut signal |
|
|
| |||||
|
|
|
|
|
|
|
|
|
| 6 to F: No Function (Prohibited setting. Do not set these values) | ||||||||
|
| Note: When “UserOutput signal” is selected, set the status of the signal with “UserOutput signal for the | ||||||||||||||||
|
|
| power/IO | connector |
|
|
|
|
| |||||||||
|
|
|
| |||||||||||||||
|
| [UserOutput signal for the |
| |||||||||||||||
F1H: TEST2[7..0] |
| Sets the status of the UserOutput signal. |
|
|
|
|
|
|
| |||||||||
|
| D[7..0] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| D7 |
| D6 | D5 |
| D4 |
| D3 |
| D2 | D1 |
| D0 |
|
|
|
|
|
| D7 to D5: | No function |
|
|
|
|
|
|
|
| Always set as “000” | ||||||
|
| D4: |
| UserOutput signal for 3pin of the power/IO connector | 0: Low | 1: High | ||||||||||||
|
| D3: |
| UswerOuput signal for 2pin of the power/IO connector | 0: Low | 1: High | ||||||||||||
|
| D2 to D0: | No function |
|
|
|
|
|
|
|
| Always set as “000” | ||||||
|
| Note: The UserOutput signal is enabled whenever “UserOutput signal” is selected at the “Output signal | ||||||||||||||||
|
| selection (OUTSEL)”. |
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
29/37 | ||
User’s Guide Rev. 1.01 | ||
|
