NOTE: Wires marked with dotted line are optional.
From | Furnace | R |
|
| G |
|
|
| or | From | Furnace |
| |
|
|
|
| |||
|
| RH |
|
| RH or | R |
|
|
|
|
| ||
|
|
|
|
|
| |
C | W |
|
|
| W |
|
|
|
|
|
| ||
|
|
|
|
| C |
|
Go To Page 11 | Go To Page 12 |
| ||||
From | Furnace |
|
And AC unit | Y | |
|
| |
|
| R |
|
| or |
|
| RH |
| C | G |
|
| |
|
| W |
Go To Page 13
From | Furnace |
|
And AC unit | Y | |
|
| |
|
| RH |
|
| RC |
| C | G |
|
| |
|
| W |
Go To Page 14
From No | rmal |
| From hea | t pump |
| Fro | m heat | pump |
|
| ||||
| stem |
|
| at |
|
| x hea | t | W or W2 | |||||
two stage sy |
| with out Aux he |
| with Au | ||||||||||
| Y |
| ||||||||||||
|
|
|
|
|
| |||||||||
|
|
| W2 |
|
|
|
|
|
|
|
| Y |
| |
|
|
|
|
|
| O |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| or |
|
|
|
|
|
|
|
|
|
| W |
|
|
| B |
|
|
|
|
| O or | B |
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| G |
|
|
|
|
|
|
|
|
| ||
C |
| C |
|
| G | C |
|
|
| G | ||||
|
|
|
|
|
|
|
| |||||||
|
|
| R |
| R |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| R |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Go To Page 15 | Go To Page 16 |
|
|
| Go To Page 17 | |||||||||
If you do not find the wiring information for your system try our website:
9 Wire Connections cont
When you have finished connecting the wires attach control unit to wall unit. Hook the top of the body onto the base, swing the body down, and snap the body onto the base.
10 Check Unit | Follow these procedures to verify you | |
have correctly installed the unit. | ||
|
To.check HEAT mode:
.Set the mode switch to HEAT. Set the fan switch AUTO.
.Using the TEMP UP button raise the set point to 90deg.
.Allow the system 5 min to respond.
.Verify that heat is blowing from the system. Set the mode switch to OFF.
PG 9
C W2 RC | O B RH | W Y G |
|
|
To.check COOL mode:
.Set the mode switch to COOL.
Press the TEMP DOWN button to a temp 5o below room
. temperature.
.Allow the system 5 min to respond.
.Verify that cool air is blowing from the system. Set the mode switch to OFF.
To.check Fan:
.Switch mode to OFF during fan test.
.Switch the FAN switch to the ON position. Verify air is blowing from vents. After test, return fan switch to AUTO, and mode to HEAT or COOL.
|
| FA | N | ON |
|
|
| ||
F | COOL | AUTO |
|
|
OF |
|
|
|
HEAT 
Mode Switch 
Fan Switch
Congratulations, you have successfully installed your unit. Please proceed to the OPERATING GUIDE
to initialize the new thermostat. REMEMBER, Mode switch must be in HEAT or COOL to operate.
PG 10
