SPECIFICATIONS

 

PUNCH P2-DVC

8"

10"

12"

15"

 

 

 

P2D28 / P2D48

P2D210 / P2D410

P2D212 / P2D412

P2D215 / P2D415

 

 

 

 

 

 

 

 

 

 

 

Nominal Impedance (ohms)

2 x 2 / 2 x 4

2 x 2

/ 2 x 4

2 x 2

/ 2 x 4

2 x 2 / 2 x 4

 

 

 

 

 

 

 

 

 

Frequency Response (Hz)

40-250

30-250

26-250

20-250

 

 

 

 

 

 

 

 

 

Voice Coil Diameter - inch

2.0 (4-Layer)

2.0 (4-Layer)

2.0 (4-Layer)

2.0 (4-Layer)

 

 

(cm)

(5.08)

(5.08)

(5.08)

(5.08)

 

 

 

 

 

 

 

 

 

Displacement - cu. ft.

0.030

0.052

0.057

0.066

 

 

(Liter)

(0.85)

(1.47)

(1.61)

(1.87)

 

 

 

 

 

 

 

 

 

Fs - Free Air Resonance (Hz)

40

30

26

20

 

 

 

 

 

 

 

 

 

 

 

Qts

0.45 / 0.47

0.48

/ 0.51

0.55

/ 0.58

0.63 / 0.62

 

 

 

 

 

 

 

 

 

 

 

Vas - cu. ft.

0.37

1.08

/ 1.13

2.39

/ 2.38

6.85

 

 

(Liter)

(10.5)

(30.5)

/ (31.9)

(67.6)

/ (67.3)

(194.0)

 

 

 

 

 

 

 

 

 

Xmax - inch

0.315

0.433

0.433

0.492

 

 

(cm)

(0.80)

(1.10)

(1.10)

(1.25)

 

 

 

 

 

 

 

 

 

SPL (dB @ 1w/1m)

84

84

86

86

 

 

 

 

 

 

 

 

 

Power Handling-Watts (RMS)

200

250

250

250

 

 

(Peak)

400

500

500

500

 

 

 

 

 

 

 

 

 

 

Specifications subject to change without notice

WIRING CONFIGURATIONS

By varying the wiring configuration of your speakers you can create an impedance load to match your system. Altering the wiring configurations gives a range of options for impedance loads. Series, Parallel, or Series-Parallel wiring configurations are different techniques for wiring speakers that provide different loads. Series configuration is a string method where speakers are wired end to end. Parallel configuration uses two or more speakers wired across common terminals. Series-Parallel configuration combines both techniques. Choose the wiring diagram that corresponds to the number of woofers and the impedance of your amplifier.

SUBWOOFER CROSSOVERS

There are two operational types of crossovers, passive and active. Passive crossovers (coils or inductors) are placed on the speaker leads between the amplifier and speaker. An active crossover is an electronic filter that separates the audio signal fed to different amplifiers. For optimum subwoofer performance, we recommend using an active 80-100Hz low-pass crossover at 12dB/octave.

5

Page 5
Image 5
Rockford Fosgate P2D215, P2D48, P2D210, P2D212, P2D28, P2D412 Specifications, Wiring Configurations, Subwoofer Crossovers