Roland FC-200 - page 31

Sending the Data

(the sending FC-200)

1, 2

1. Switch off the FC-200 that will be used to send the data.

2. While keeping Number pedal “9” depressed, switch the power back on.

The indicator for the Control pedal flashes, and [ ] (Bulk Dump) appears on the display.

3. Press the Control pedal.

The indicator for the Control pedal stops flashing and remains lit continuously, the display readout

changes, and the data transmission (bulk dump) starts. When the transmission of data finishes, the

devices return to their normal state of operation.

Contents

Main Page Introduction MAIN FEATURES CONTENTS IMPORTANT NOTES Power Supply Placement Maintenance Additional Precautions DESCRIPTIONS Front Panel Rear Panel HOW TO USE THE FC-200 MAKING THE CONNECTIONS External MIDI Device External MIDI Device Loading Batteries Connecting an AC Adaptor SWITCHING ON THE POWER or About the ECONOMY Setting The Flow of MIDI Messages SWITCHING MODES Determining the Current Mode PROGRAM CHANGE MODE About Program Change Numbers How to Send Program Change Messages 1. 2. Using the Control Pedal Page CONTROL CHANGE MODE Controller Numbers of the Pedals #65 #66 #67 #68 #69 #76 #80 #72 #73 #74#71#70 #75 Page NOTE MODE Note Range Changing the Note Range by Octaves During a Performance FOOT SW/EXP 5: Octave Shift-Up Function FOOT SW/EXP 6: Octave Shift-Down Function Page EDIT FUNCTION How to Make Changes 2, 6 1, 2 34 4 Page PARAMETERS WITH SETTINGS THAT CAN BE CHANGED MIDI Channel: 1 to 16 [ ] (MIDI Channel) Controller Number Setting for Control Pedal: 1 to 31, 30 to 80 to 95 Setting for Latch Type Control Pedal Operation: On / Off Bank Select: On / Off [ ] (Bank Select) BANK SELECT PROGRAM CHANGE BANK SELECT Bank Limit: 0 to 12 to 99 [ ] (Bank Limit) Output of Program Change Messages When Changing Banks: On / Off [ ] (Bank Output) Changing Banks Using the Number Pedals: On / Off [ ] (Bank Change) * Pressing a Number pedal higher than the value set for Bank Limit has no effect. Controller Number Settings: 1 to 31, 33 to 95 Setting for Latch Type Pedal Operation: On / Off Note Range Setting: C0 to C2 to C8 [ ] (Note Range) Octave Shift Upper Limit Setting: C0 to C6 to C8 [ ] (High) C1 C2 C3 C4 C5 C6 C7 C8 Octave Shift Lower Limit Setting: C0 to C2 to C8 [ ] (Low) MODE Jack Loop Setting: 1 / 2 / 3 / 4 [ ] (Jack Loop) ABOUT REALTIME MESSAGES AND MMC MESSA GES About Realtime Messages About MMC (MIDI Machine Control) Messages How to Make the Settings Realtime Messages DATA TRANSFER USING MIDI Sending Data (Bulk Dump) MIDI OUT MIDI IN Making the Connections and Getting Ready For Storage on a MIDI Sequencer Page Receiving Data (Bulk Load) ABOUT CHANGING THE BATTERIES USING MIDI About MIDI The Exchange of MIDI Data About MIDI Connectors * The FC-200 has MIDI IN and MIDI OUT ports. MIDI Messages Recognized by the FC-200 CHANNEL MESSAGES Program Change Messages Control Change Messages Note Messages MIDI Implementation Chart RETURNING SETTINGS TO THEIR F ACTORY DEFA ULT V ALUES (INITIALIZATION) IF YOU THINK THERES A PROBLEM, CHECK THESE FIRST ROLAND EXCLUSIVE MESSAGES 1. Data Format for Exclusive Messages MIDI status: F0H, F7H Manufacturer ID: 41H Device ID: DEV 3. One-way Transfer Procedure Request data 1: RQ1 (11H) Data set 1: DT1 (12H) Example of Message Transactions MIDI FOOT CONTROLLER Date : Jan.20, 1995 Model FC-200 MIDI Implementation Version : 1.00 1. RECOGNIZED RECEIVE DATA SYSTEM REALTIME MESSAGE ACTIVE SENSING SYSTEM EXCLUSIVE MESSAGE SYSTEM EXCLUSIVE MESSAGE MIDI MACHINE CONTROL (MMC) * FC-200 can set the following MMC commands. * Does not transmit while in EXCLUSIVE Mode. 3. EXCLUSIVE COMMUNICATIONS MODE STATUS (Individual area) BANK NUMBER (Individual area) EDIT PARAMETERS (Individual area) * Only Controller Number can be assigned to each Expression pedal. FLIP-FLOP STATUS (Individual area) EDIT PARAMETERS (Bulk area) MIDI Implementation Chart Notes MIDI FOOT CONTROLLER Date : Jan.20 1995 MODEL FC-200 Version : 1.00 SPECIFICATIONS NOTICE AVIS FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT