Rotel AC Power and Control, RA-06 Stereo Integrated Amplifier, Remote Sensor, Placement

RA-06Stereo Integrated Amplifier

Remote Sensor 6

The Remote Sensor picks up the infrared signals from the remote control. Do not cover or block the sensor. It must be unobstructed or the remote control will not work properly. The operation of the Remote Sensor can also be affected if it is exposed to bright light, particularly sunlight. Certain types of lighting, such as halogen lights, that emit a fair amount of infrared light, can also interfere with proper operation. In addition remote control functions may not work reliably if the batteries in the RR-AT94 are weak.

A Few Precautions

WARNING: To avoid potential damage to your system, turn off ALL the components in the system when connecting or disconnect- ing the loudspeakers or any associated components. Do not turn the system compo- nents back on until you are sure all the con- nections are correct and secure. Pay particular attention to the speaker wires. There must be no loose strands that could contact the other speaker wires, or the chas- sis of the amplifier.

Please read this manual carefully. It provides information on how to incorporate the RA-06 into your system as well as information that will help you get optimum sound performance. Please contact your authorized Rotel dealer for answers to any questions you might have. In addition, all of us at Rotel welcome your questions and comments.

Save the RA-06 shipping carton and all en- closed packing material for future use. Shipping or moving the RA-06 in anything other than the original packing material may result in severe damage to your amplifier.

Fill out and send in the owner’s registration card packed with the RA-06. Also be sure to keep the original sales receipt. It is your best record of the date of purchase, which you will need in the event warranty service is ever required.

6

Placement

Like all audio components that handle low- level signals, the RA-06 can be affected by its environment. Avoid placing the RA-06 on top of other components. Also avoid routing audio signal cables near power cords. This will minimize the chance it will pick up hum or interference.

The RA-06 generates heat as part of its nor- mal operation. The heat sinks and ventilation openings in the amplifier are designed to dissipate this heat. The ventilation slots in the top cover must be open. There should be 10 cm (4 inches) of clearance around the chassis, and reasonable airflow through the installation location, to prevent the amplifier from overheating.

Remember the weight of the amplifier when you select an installation location. Make sure that the shelf or cabinet can support it. We recommend installing the RA-06 in furniture designed to house audio components. Such furniture is designed to reduce or suppress vibration which can adversely affect sound quality. Ask your authorized Rotel dealer for advice about component furniture and proper installation of audio components.

Cables

Be sure to keep the power cords, digital signal cables and regular audio signal cables in your installation away from each other. This will minimize the chance of the regular audio signal cables picking up noise or interference from the power cords or digital cables. Using only high quality, shielded cables will also help to prevent noise or interference from degrad- ing the sound quality of your system. If you have any questions see your authorized Rotel dealer for advice about the best cable to use with your system.

AC Power and Control

AC Power Input p

The RA-06 does not draw high levels of current from the power outlet. However, whenever pos- sible, it should be plugged directly into a 2-pin polarized wall outlet. Do not use an extension cord. A heavy duty multi-tap power outlet strip may be used if it (and the wall outlet) can handle the current demanded by theRA-06 and all the other components connected to it.

Your RA-06 is configured at the factory for the proper AC line voltage in the country where you purchased it (either 120 volts AC or 230 volts AC with a line frequency of either 50 Hz or 60 Hz). The AC line configuration is noted on a decal on the back panel.

NOTE: Should you move your RA-06 amplifier to another country, it is possible to reconfigure it for use on a different line voltage. Do not attempt to perform this conversion yourself. Opening the enclosure of the RA-06 exposes you to dangerous voltages. Consult a quali- fied service person or the Rotel factory service department for information.

If you are going to be away from home for an extended period of time such as a month-long vacation, it is a sensible precaution to unplug your amplifier (as well as other audio and video components) while you are away.

Power Switch 2a and Power Indicator 1

Press the front panel Power Switch 2button, to turn the RA-06 on. The Power Indicator light 1is illuminated when the RA-06 is on. Press Power Switch button again to turn the RA-06 off.

Once the RA-06 has been turned on with the front panel power switch, it can be switched between normal operating mode and standby mode with the Power button aon the RR-AT94 remote control.

See the “12V Trigger Outlet” section for more information on ways you may be able to turn on and off other components in your system along with the RA-06.