81 | DRAINAGE |
|
82 | PROGRAMMING THE MACHINE |
|
31
Install the water tank, slightly pressing over it to fit the valve which will open automatically.
Important: It is advisable to drain the machine before the first start, after a prolonged period the machine has not been used or whenever the water
keys | . The keyENTallows you to activate the | "PLEASE | ACTIVADE | " | |
selected item. It is possible to modify the selected | "SYSTEM | 2 | " | ||
figuresinamenuitemusingthekeys | .Thekey |
|
|
| |
Do not fill the tank with an excessive quantity of water.
Always fill the tank with fresh water only: hot water as well as other fluids might damage the tank. Never use carbon dioxide added water.
tank has been completely emptied.
Furthermore, should the pump be defective, the display shows:
"VENTILATE "
Programming the machine
32
To enter the programming mode, press the key ENT ( 
pre-ground
ENT memorizes the selected options (for instance “ON” for the cup heating plate).
Should you accidentally change some data, press ESC (*…) to leave the menu item without saving the new options which were selected accidentally.
Language selection
Move the asterisk to he menu item
“LANGUAGE” using the keys
. Press
ENT to activate this item. The following message will be displayed:
Water hardness adjustment
In order to adjust the water hardness, it is necessary to test the water using the strip supplied with the machine. Dip the strip into the water for a second, shake off excess water gently, wait approx. 1 minute and read the results.
Move the asterisk at the end of the line to the menu item “WATER HARDN.” using the keys
and select it by means of the ENT
button.
The following message will be displayed:
Do not switch on the machine on if the water tank is empty: always make sure there is enough water in the tank!
Connect the plug to the socket and press the main switch. The following message will be displayed:
"WARMING UP....... | " |
Should
"1 | LANGUAGE | " |
"2 SYSTEM 2 | " | |
At the end of the line a blinking asterisk is displayed, which can be moved up and down
with the keys
(tall and regular coffee). If the asterisk is on the first menu, press
button
to move it on the second menu and vice versa. The display shows the following sequence of messages:
"1 LANGUAGE | " |
"ENGLISH | " |
The keys allow you to change the set options :
“ENGLISH” , “ITALIANO” , “FRANÇAIS”, “DEUTSCH”,“NEERLANDAIS”,“ESPAÑOL”, “PORTUGUES”.
Enabling of second heating system
Royal Cappuccino is equipped with two boilers
"3 WATER HARDN./ "
"HARDNESS 3 | " |
The keys
allow you to change the set options:
HARDNESS 4 |
(hard water) |
HARDNESS 3 |
(medium water) |
Hardness 4 |
"ENERGY |
| " | 1 | LANGUAGE | 10 PROG. H. WATER | ||
"SAVING |
| " | |||||
| 2 | SYSTEM 2 | 11 PROG. CAPPUC. | ||||
|
|
|
|
| |||
be displayed, press button |
|
| “Standby” | to | 3 | WATER HARDN. | 12 TOTAL COFFEE |
|
| 4 | CUP HEATER | 13 DESCALING | |||
disactivate the energy saving mode. |
| ||||||
| 5 | TEMP. L. COFFEE | 14 SIGN. DESCAL. | ||||
|
|
|
|
| |||
|
|
|
|
| 6 | TEMP. COFFEE | 15 TIMER |
with independent circuits. One of these boilers can be disconnected. By pressing
keys
move the asterisk at the end of the
line to the menu item “SYSTEM 2”. Press ENT to activate this item. The following message will be displayed:
Hardness 3 | HARDNESS 2 |
(soft water) | |
Hardness 2 | HARDNESS 1 |
Hardness 1 | (very soft water) |
Drainage | 7 | TEMP. S. COFFEE | 16 VENDING |
| |||
Direct the steam/hot water spout on the drip tray | 8 | PREBREWING | 17 EXIT |
9 | PREGRINDING |
| |
(2). Place a cup or another suitable container |
| ||
|
|
| |
under the dispensing tube, then turn the steam/ |
|
|
|
"2 SYSTEM 2 | " | Cup heating plate connection |
Royal Cappuccino is equipped with a useful cup | ||
"ON | " | heating plate which can be disconnected, if |
|
| required. |
hot water knob counterclockwise. The pump | To leave the menu, move the asterisk at the end | ||||
of the line to item <<Exit>> using the key | . |
| |||
starts automatically. Wait until a regular water jet |
| ||||
|
|
| |||
is obtained, then close the knob. The machine is Then, press ENT ( | |||||
now drained and ready to work. |
| machine is now in the normal mode again. |
|
| |
The following message will be displayed: |
| Selecting single menus |
|
| |
|
|
|
|
| |
| "SELECT PRODUCT | " | Select the different menu items by means of the | ||
| "READY FOR USE | " | |||
|
|
|
| ||
|
|
|
|
|
|
The keys
allow you to change the set
options: ON, OFF.
If the second boiler is disconnected it is not possible to dispense steam and therefore cappuccino can’t be prepared. Should the cappuccino selection button be pressed
or the steam/hot water knob be opened, the display shows the following message:
Press keys
to move the asterisk to item
“CUP HEATER”. Press ENT to activate this function.
The following message will be displayed:
"4 CUP HEATER | " |
"ON | " |