79

MACHINE CONTROLS AND PARTS

 

80

INSTALLATION

 

IMPORTANT SAFEGUARDS

a)A short power-supply cord (or detachable power-supply cord) is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord.

b)Longer detachable power-supply cords or extension cords are available and may be used if care is exercised in their use.

c)If a long detachable power-supply cord or extension cords is used,

1)The marked electrical rating of the detachable power-supply cord or extension cord should be at least as great as the electrical rating of the appliance,

2)If the appliance is of the grounded type, the extension cord should be a grounding- type 3-wire cord, and

3)The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over.

Unpacking/installation

Standard packing is strong enough to protect the machine during mail shipping. Keep this package to return the machine to the manufacturer, whenever necessary.

Before installing the machine, keep to the safety indications at page 77.

Whenever possible, use the machine with swivel (24). When installing the machine, make sure the swivel is always fitted in the provided area on the lower side of the machine.

circuit! Overheated steam and hot water may cause burns. Do not direct steam or water jet towards the body; furthermore, great attention must be given when touching either the steam/ hot water spout or the heating plate: danger of burns!

Never use the machine without water or coffee beans.Remove measuring spoon, brush and the central
1Coffee grounds container2Drip tray3Cup holder surface4Main switch5Power cord6Coffee dispensing unit7Steam/hot water spout wit burn-protection8Control panel9Steam knob10Cup heating plate11Water tank12Water tank cover13Water level14Pre-ground coffee container with cover15Coffee bean container coverDescription of the control panelDigital displayStandby switch:energy saving function on/offSelection key for 1 or 2 cups of tall coffee or key “ ” in the programming mode

Selection key for 1 or 2 cups of regular coffee or key “” in the programming mode

Selection key for 1 or 2 cups of espresso coffee or “ESC” in the programming mode

Pre-ground coffee selection button or “ENT” in the programming modeCappuccino selection keyHot water on/off key
16Coffee bean container17Grind adjustment lever18Coffee dosage adjustment lever19Service door20Filling funnel21Handle for assembling and disassembling of central unit22Central unit23Coffee rest drawer24Swivel25Cappuccinatore26Suction pipe27Dispenser28Cappuccinatore adjusting valve29Cappuccinatore coverWARMING UP......

 

ESC

ENT

............................ ............................

............................

............................

Power supply connectionWarning: electric current may cause d e a t h ! Always keep to safety rules.

The coffee machine must be connected to an adequate socket. Voltage must suit to the voltage specified on the appliance rating plate.

Never use defective power cords! Defective power cords and plugs must be replaced by an authorised personnel.

Should an extension cord be used, check its perfect conditions. The extension cord must have a minimum section of 1,5 mm2 or 16 AWG and must be supplied with a three-pole plug/socket.

Starting and useParts under current shall never be in contact with water: danger of short-
unit key from the coffee grounds container (1) and keep them within reach.Unwind the power cord (5) from the rear side of the machine.

30

Remove the cover (15) and fill the container with coffee beans (300 g approx.), then, replace the cover. Adjust grinding by means of the grind adjustment lever (17), positioning it on point “5” of the scale.

Never fill the coffee bean container with other products since they might damage the machine!

Before filling the container with coffee beans, make sure the pre-ground coffee container (14) is closed to prevent coffee beans from falling into it. They might damage the machine!

Remove water tank (11) from the machine, remove its cover (12) and fill it with cold water (approx. 2.4l). A valve on the tank bottom prevents water from escaping.

Before installing the water tank in the machine, make sure the coffee bean container cover is properly fitted.