Runco VX-33I - page 50

34 Runco VX-33i Installation/Operation Manual

PRELIMINARY

Connecting 12-volt

Trigger Outputs to

External Equipment

If your VX-33i is equipped with a CineWide with AutoScope system, connect the

AutoScope lens motor to a 12-volt trigger output on the VX-33i; see Figure 3-16.

Similarly connect other 12-volt trigger-activated equipment (such as retractable screens or

screen masks) to the other trigger outputs.

For more information on using the 12-volt triggers, refer to Triggers on page 58.

Figure 3-16. 12-volt Trigger Output Connections

➤

Rear Panel

HD1 (RCA)

AutoScope Lens Motor (Rear)

Tip = +12V

Sleeve = Ground

3.5-mm

mini plug

AC Input

Power

Switch

Retractable Screen or other

12-volt trigger-activated

device

Contents

Main Page RuncoCare Standard Two Year Limited Warranty Page Page Page Important Safety Instructions Compliance Information Page Page Page Page Page Page Page Page 1.1 About This Manual 1. Introduction 1.2 Using This Manual WARNING DANGER! 1.3 Description, Features and Benefits Page 2.1 VX-33i at a Glance 2. Controls and Functions 2.2 VX-33i Rear Panel Page 2.3 VX-33i Rear Connector Panel Page 10 Runco VX-33i Installation/Operation Manual 2.4 VX-33i Remote Control Figure 2-4. VX-33i Remote Control LIGHT OFF ON SOURCE PICTURE MEMORY ASPECT RATIO Page Page 3. Installation 3.1 Remote Control 3.2 Quick Setup Table 3-1. Installation Overview 3.3 Installation Considerations Table 3-2. Projector Installation Options Table 3-3. VX-33i Lens Options and Throw Ratios Ceiling Installation Floor Installation Figure 3-4. Horizontal Lens Shift (EXAMPLE ONLY) Table 3-4. VX-33i Vertical and Horizontal Lens Shift Limits 3.4 Installing the Primary Projection Lens Page 3.5 Installing the Optional CineWide Lens Mount Page Page Page Page 3.6 Mounting the VX-33i 3.7 Connections to the VX-33i Runco VX-33i Installation/Operation Manual 29 Digital (DTV) RGB or Component Video Connections: See Figure 3-11 and Figure 3-12. Figure 3-11. Digital (DTV) RGB or Component Video Connections (HD1, HD2) Page Page Page to Automation/ Control System or PC Page Page 3.8 Turning on the Power 3.9 Adjusting the Picture Orientation VX33i Component RCA 16:9 480I 3.10 Primary Lens Adjustments 3.11 Installing and Adjusting the CineWide Anamorphic Lens Page Page Page Page Wrong Position Correct Position Page 4. Operation Figure 4-1. VX-33i OSD Menu Structure Input Source Calibration Memory Presets Input Position 7 Table 4-1. Aspect Ratio Settings Table 4-1. Aspect Ratio Settings (continued) Page Page Page Page 7 Page Page Page Page 5.1 Lamp Replacement 5. Maintenance and Troubleshooting WARNING 5.2 Filter Replacement Side Filter Access Panel 5.3 Troubleshooting Tips Table 5-1. Troubleshooting Chart Page 6. Serial Communications 6.1 RS-232 Connection and Port Configuration 6.2 Serial Command Syntax Table 6-1. Serial Commands and Responses Page STATUS 1 STATUS 2 STATUS 3 STATUS 4 STATUS 5 STATUS 10 STATUS Page 7.1 VX-33i Specifications Table 7-1 lists the VX-33i specifications. 7. Specifications Table 7-1. VX-33i Specifications Table 7-1. VX-33i Specifications (continued) Runco VX-33i Installation/Operation Manual 71 7.2 VX-33i Dimensions Figure 7-1 shows the VX-33i dimensions (all dimensions are in inches). Figure 7-1. VX-33i/CineWide with AutoScope Dimensions 7.3 Supported Timings Table 7-2 lists the signal types supported by each input on the VX-33i. Table 7-2. Supported Signal Timings by Input Table 7-2. Supported Signal Timings by Input (continued)