Runco VX-33I - page 51

Runco VX-33i Installation/Operation Manual 35

PRELIMINARY

Connecting an External IR

Receiver to the VX-33i

If infrared signals from the remote control cannot reach the projector due to excessive

distance or obstructions such as walls or cabinet doors, you can connect an external IR

receiver to the WIRED REMOTE input on the VX-33i to extend the range of the remote

control. See Figure 3-17.

Figure 3-17. External IR Receiver Connection

Connecting to AC PowerProjector: Plug the female end of one power cord into the AC receptacle on the rear of

the VX-33i (AC 100V ~ 240V). Then, connect the other end to your AC power source.

AutoScope Lens Motor: With AutoScope-equipped projectors, an additional power

cord is provided for the lens motor. Plug the female end of the AC power cord into the AC

input on the rear of the lens motor assembly. Connect the other end to a 110 VAC power

source.

When an external IR receiver is connected to the wired IR input, the

built-in IR sensor on the VX-33i is disabled.

Rear Panel

WIRED REMOTE

WIRED REMOTE

Service port.

Not for user

access

Ring = +5V

Tip = IR Input

Sleeve = Ground

(3.5-mm

mini phono

plug)

IR Receiver

Remote

Control

FOCUS LENSZOOM

LIGHTOFF

ON

VIDS

-VIDH

DMI1

HD2

SOURCE

PICTURE MEMORY

ASPECT RATIO

HD1

INFO

ENTER

EXITM

ENU

BRT

CUST1CUST2

CONTC

OLT

INT

HD3

HDMI2

ISF

DAY

ISF

NIGHT

16:9IWIDE

LBOX

4:3

CINEMAIWIDE

2.35

FOCUSZOOM

2

1

5

46

3

9

80

7

LENS

Note

The input voltage to the AutoScope lens motor must be between

100 and 120 VAC. Do not connect the AutoScope lens motor

to a 200-240 VAC power source!

Caution

Contents

Main Page RuncoCare Standard Two Year Limited Warranty Page Page Page Important Safety Instructions Compliance Information Page Page Page Page Page Page Page Page 1.1 About This Manual 1. Introduction 1.2 Using This Manual WARNING DANGER! 1.3 Description, Features and Benefits Page 2.1 VX-33i at a Glance 2. Controls and Functions 2.2 VX-33i Rear Panel Page 2.3 VX-33i Rear Connector Panel Page 10 Runco VX-33i Installation/Operation Manual 2.4 VX-33i Remote Control Figure 2-4. VX-33i Remote Control LIGHT OFF ON SOURCE PICTURE MEMORY ASPECT RATIO Page Page 3. Installation 3.1 Remote Control 3.2 Quick Setup Table 3-1. Installation Overview 3.3 Installation Considerations Table 3-2. Projector Installation Options Table 3-3. VX-33i Lens Options and Throw Ratios Ceiling Installation Floor Installation Figure 3-4. Horizontal Lens Shift (EXAMPLE ONLY) Table 3-4. VX-33i Vertical and Horizontal Lens Shift Limits 3.4 Installing the Primary Projection Lens Page 3.5 Installing the Optional CineWide Lens Mount Page Page Page Page 3.6 Mounting the VX-33i 3.7 Connections to the VX-33i Runco VX-33i Installation/Operation Manual 29 Digital (DTV) RGB or Component Video Connections: See Figure 3-11 and Figure 3-12. Figure 3-11. Digital (DTV) RGB or Component Video Connections (HD1, HD2) Page Page Page to Automation/ Control System or PC Page Page 3.8 Turning on the Power 3.9 Adjusting the Picture Orientation VX33i Component RCA 16:9 480I 3.10 Primary Lens Adjustments 3.11 Installing and Adjusting the CineWide Anamorphic Lens Page Page Page Page Wrong Position Correct Position Page 4. Operation Figure 4-1. VX-33i OSD Menu Structure Input Source Calibration Memory Presets Input Position 7 Table 4-1. Aspect Ratio Settings Table 4-1. Aspect Ratio Settings (continued) Page Page Page Page 7 Page Page Page Page 5.1 Lamp Replacement 5. Maintenance and Troubleshooting WARNING 5.2 Filter Replacement Side Filter Access Panel 5.3 Troubleshooting Tips Table 5-1. Troubleshooting Chart Page 6. Serial Communications 6.1 RS-232 Connection and Port Configuration 6.2 Serial Command Syntax Table 6-1. Serial Commands and Responses Page STATUS 1 STATUS 2 STATUS 3 STATUS 4 STATUS 5 STATUS 10 STATUS Page 7.1 VX-33i Specifications Table 7-1 lists the VX-33i specifications. 7. Specifications Table 7-1. VX-33i Specifications Table 7-1. VX-33i Specifications (continued) Runco VX-33i Installation/Operation Manual 71 7.2 VX-33i Dimensions Figure 7-1 shows the VX-33i dimensions (all dimensions are in inches). Figure 7-1. VX-33i/CineWide with AutoScope Dimensions 7.3 Supported Timings Table 7-2 lists the signal types supported by each input on the VX-33i. Table 7-2. Supported Signal Timings by Input Table 7-2. Supported Signal Timings by Input (continued)