Russound CA-LCD.2, CA-KP.2 Rear Panel Connections, Source Input Connections, Speaker Connections

REAR PANEL CONNECTIONS

Figure 3 - CA6.4i Rear Panel Connections

Source Input	Keypad Zone Input	Variable/Fixed	Zone Preamp Outputs	Voltage Selector Switch
Connections		Output Switch

CA6.4i NEWMARKET, NH U.S.A.

SOURCE INPUTS

1 2 3 4

R

L

		1
	LINK	IR EMITTERS
IN	OUT

KEYPAD PORTS

1 2 3 4 5 6

OUTPUT TO 8 OHM SPEAKER

2 3 4 5

VARIABLE

FIXED

6

ZONE PREAMP

OUTPUTS

1	2	VARIABLE	~220-240VAC		~110VAC
	R
		FIXED
	L
	MUTE				VOLTAGE	FUSE
IN		12V TRIG			110V	F4A
	OUT		WARNING : SHOCK HAZARD – DO NOT OPEN	~110VAC	220-240V	F2A

AVIS : RISQUE DE CHOC ELECTRIQUE –	~220-240VAC
NES PAS OUVRIR.	~50-60Hz
SERIAL #	400W

IR Link	Emitter Outputs	Speaker Output Connectors		12 Volt Trigger	AC110/240	Fuse
			Mute Inputs	Output	Input	Holder
In and Out

Figure 4 - CA4.4i Rear Panel Connections

Source Input	Keypad Zone Input	Zone Preamp Outputs	Voltage Selector Switch
Connections

		CA4.4i NEWMARKET, NH U.S.A.			KEYPAD PORTS
	SOURCE INPUTS
				1	2	3	4
1	2	3	4

R

L

OUTPUT TO 8 OHM SPEAKER

		1	2	3
	LINK	IR EMITTERS
IN	OUT

ZONE PREAMP	ZONE PREAMP
OUTPUTS	OUTPUTS

1	2		3	4	VARIABLE	~220-240VAC	~110VAC
VARIABLE		VARIABLE	VARIABLE
	R			R
FIXED		FIXED	FIXED		FIXED

L		L
4					VOLTAGE	FUSE
	MUTE
IN		12V TRIG			110V	F4A
	OUT		WARNING : SHOCK HAZARD – DO NOT OPEN	~110VAC	220-240V	F2A
			AVIS : RISQUE DE CHOC ELECTRIQUE –	~220-240VAC
			NES PAS OUVRIR.	~50-60Hz

SERIAL #	400W	DESIGNED IN USA
		MADE IN KOREA

IR Link	Emitter Outputs	Speaker Output Connectors	Variable/Fixed		12 Volt Trigger	AC110/240	Fuse
			Output Switch	Mute Inputs	Output	Input	Holder
In and Out

SOURCE INPUT CONNECTIONS

Your source inputs are located at the top left corner of the back panel. Connect each source output, left and right, using quality signal cables / patch cables to the CAi source input. Label each cable the name of your source and the input number of the CAi you have selected. Repeat until all sources are connected. List them down below.

List 1 – Source names should be written below

Input 1 ________________ Input 2 ________________

Input 3 ________________ Input 4 ________________

SPEAKER CONNECTIONS

Each speaker connection on the back panel corresponds to one room/zone. Wire your speakers by first removing the connector for the chosen zone. Using wire strippers, strip back 1/4" of the end of the wire. Insert the proper polarity, left + to left +, left- to left- etc., until all wires are connect- ed in each zone output. Label each wire with the room name and zone number. Write down the room name to the zone number below. Note: We recommend 8 Ohm minimum speakers for each zone. However, speakers as low as 4 Ohm can be safely used in up to two zones, if necessary.

List 2 – Wire color should be written below

(Color) Left + _______________ Left - _______________

Right + _______________ Right - _______________

List 3 – Room names should be written below

Zone 1 ________________ Zone 2 ________________

Zone 3 ________________ Zone 4 ________________

6