Cutting warped material, See Figures 37, Wrong | Ryobi TS1141

OPERATION

	Bevel
	Angle		Type of Cut
	Setting

		Left side, inside corner
	33.85°	1.	Top edge of molding against fence
	33.85°	2.	Miter table set right 31.62°
		2.	Miter table set right 31.62°
		3.	Save left end of cut

		Right side, inside corner
	33.85°	1.	Bottom edge of molding against fence
	33.85°	2.	Miter table set left 31.62°
		2.	Miter table set left 31.62°
		3.	Save left end of cut

		Left side, outside corner
	33.85°	1.	Bottom edge of molding against fence
	33.85°	2.	Miter table set left 31.62°
		2.	Miter table set left 31.62°
		3.	Save right end of cut

		Right side, outside corner
	33.85°	1.	Top edge of molding against fence
	33.85°	2.	Miter table set right 31.62°
		2.	Miter table set right 31.62°
		3.	Save right end of cut

cutting warped material

See Figures 37 - 38.

When cutting warped material, always make sure it is posi- tioned on the miter table with the convex side against the fence as shown in figure 37.

If the warped material is positioned the wrong way as shown in figure 38, it will pinch the blade near the completion of the cut.

WARNING:

To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against the fence.

Right

Fig. 37

WRONG	Fig. 38

28

Image 28

Ryobi TS1141 manual Cutting warped material, See Figures 37, Wrong

Contents

OPERATOR’S Manual Save this Manual for Future Reference Table of Contents Introduction General Safety Rules Read ALL Instructions  Never Start a Tool When ANY ROTATiNG COM Specific Safety RulesPonent is in Contact with the Workpiece Specific Safety Rules Symbols Symbol Signal Meaning Cord Length Wire Size A.W.G ElectricalDouble Insulation Electrical Connection Glossary of Terms Features Product SpecificationsBlade Wrench Work Clamp Know Your Compound Miter SAW AMP MotorBevel Lock Knob Blade Wrench Storage Tools Needed Switch TriggerSpindle Lock Button Dust BAG Miter saw Head Blade Rear bracket Carrying handle Assembly Installing the rear bracket/carrying handleUnpacking Screws Rear bracket Carrying handle Mounting Holes Mounting the miter saw base to the standBase Indicator Bevel Screw Assembling the miter saw head to the baseSee Figures 10 Unpacking Dust BAG INSTALLing Batteries in LaserWork Clamp Aligning the laser guide line Removing Your MarkTo Cut Your Mark To Leave Your Mark To Install/replace the Blade See Figures 16 Squaring the Miter Table to the Fence See Figures 18 Squaring the Blade to the Fence See Figures 21 Squaring the Blade to THE MITER Table See Figures 25 Operation ApplicationsTo Cross cut See Figures 29 Indicator ScaleSCREW indicator Bevel Cut Lock knobTo Bevel Cut See Figures 31 See Figures 33 To Compound Miter CutCompound Miter Cut Work Clamp To Support Long Workpieces 45 x 45 Compound Miter CUTLong Workpiece Supports Cutting Compound Miters COMPOUND-ANGLE Settings for Popular StructuresPitch Number of Sides Cutting crown molding Laying molding flat on the miter tableLeft SIDE, Inside Corner Right SIDE, Outside Corner Right SIDE, Inside Corner Left SIDE, Outside Corner See Figures 37 Cutting warped materialWrong Adjustments Positive Stop AdjustmentsPivot Adjustments Travel Pivot Adjustment Bevel Pivot Adjustment To adjust the miter lock lever To Adjust the Laser GuideLaser adjustment Screw Unlock Miter Lock Lever Maintenance General MaintenanceBrush Replacement Lubrication Service Model NO. and Serial no