OPERATION

■Recheck miter angle setting. Make a test cut in scrap material.

■Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side against the fence. If the concave edge of a board could collapse on the blade at the end of the cut, jamming the blade. See Figures 36 and 37.

■When cutting long pieces of lumber or molding, support the opposite end of the stock with a roller stand or with a work surface level with the saw table. See Figure 34.

■Align the cutting line on the workpiece with the edge of saw blade.

■Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece when possible. See Figure 32.

WARNING:

To avoid serious personal injury, always keep your hands outside the no hands zone; at least 3 in. (7.6 cm) from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

■Before turning on the saw, perform a dry run of the cutting operation just to make sure that no problems will occur when the cut is made.

■Grasp the saw handle firmly then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.

■Slowly lower the blade into and through the workpiece. See Figures 32 and 33.

■Release the switch trigger and allow the saw blade to stop rotating before raising the blade out of workpiece. Wait until the electric brake stops blade from turning before removing the workpiece from miter table.

SUPPORT LONG WORKPIECES

See Figure 34.

Long workpieces need extra supports. Supports should be placed along the workpiece so it does not sag. The support should let the workpiece lay flat on the base of the saw and work table during the cutting operation. Use the optional work clamp or a C-clamp to secure the workpiece.

WARNING:

To avoid serious personal injury, always keep your hands outside the no hands zone; at least 3 in. (7.6 cm) from blade. Never perform any cutting operation freehand (without holding workpiece against the fence). The blade could grab the workpiece if it slips or twists.

30

15

0

45

0 3

22.5 1 5

0

15

45

30

45° x 45° COMPOUND MITER CUT

Fig. 33

45

30

15

 

LONG WORKPIECE

 

 

 

 

 

 

45

0

 

1

0

 

 

3

 

15

45

30

 

WORKPIECE SUPPORTS

Fig. 34

 

Page 23

Page 22 Page 24
Page 23
Image 23
Ryobi TS1351 manual Support Long Workpieces, See Figure
Page 22 Page 24

TS1351 specifications

The Ryobi TS1351 is a versatile and robust table saw designed to meet the needs of both DIY enthusiasts and professional woodworkers. Known for its impressive performance and user-friendly features, the TS1351 stands out in its category, making it an ideal choice for those looking to enhance their woodworking capabilities.

One of the key features of the Ryobi TS1351 is its powerful 15 Amp motor, which delivers ample cutting power for a variety of tasks. This motor enables users to cut through hardwoods, softwoods, and even engineered materials with ease. The saw offers a maximum cutting depth of 3-1/8 inches at 90 degrees, allowing for substantial cuts in thicker materials.

The TS1351 is equipped with a 10-inch carbide-tipped blade that provides a fine finish and extended blade life. The blade can be adjusted for height and angle, allowing for precise bevel cuts of up to 45 degrees. This versatility makes it possible to perform a wide range of cuts, including crosscuts, rip cuts, and miter cuts, making the saw suitable for diverse woodworking projects.

Safety is a priority with the Ryobi TS1351. It features a blade guard and an anti-kickback pawl, which help protect users during operation. The push stick, included with the saw, further enhances safety by allowing operators to make cuts without putting their hands near the blade. Additionally, the sturdy base offers stability, reducing vibrations and ensuring accurate cuts.

Another innovative characteristic of the TS1351 is its portability. Weighing in at just over 50 pounds, the saw is easy to transport, making it suitable for job sites or home workshops. The onboard storage for accessories also helps keep the workspace organized and reduces setup time.

The Ryobi TS1351 further enhances user experience with its quick-release guard, easy-to-read scales, and a large table surface that provides ample room for material support. Whether tackling small projects or larger builds, this table saw delivers reliable performance, precision, and safety, making it a valuable tool for any woodworker or craftsperson.
Top Page Image Contents