Manuals / Ryobi / Power Tools / Saw

Ryobi TS1351 manual Squaring the Blade to the Miter Table, See Figures 25

Models: TS1351

1 28
Download 28 pages 43.7 Kb
Page 18
Image 18

ADJUSTMENTS

SQUARING THE BLADE TO THE MITER TABLE

See Figures 25 - 27.

■Unplug your saw.

WARNING:

Failure to unplug your saw could result in accidental starting causing possible serious personal injury.

■Pull the saw arm all the way down and engage the lock pin to hold the saw arm in transport position.

■Loosen the miter lock handle approximately one-half turn.

■Depress the miter lock plate and rotate the miter table until the pointer on the control arm is positioned at 0°.

■Release the miter lock plate and securely tighten the miter lock handle.

■Loosen bevel lock knob and set saw arm at 0° bevel (blade set 90° to miter table). Tighten bevel lock knob.

■Place a combination square against the miter table and the flat part of saw blade.

Note: Make sure that the square contacts the flat part of the saw blade, not the blade teeth.

■Rotate the blade by hand and check the blade-to-table alignment at several points.

■The edge of the square and the saw blade should be parallel as shown in figure 25.

■If the top or bottom of the saw blade angles away from the square as shown in figures 26 and 27, adjustments are needed.

■Loosen the lock nut securing positive stop adjustment screw. Also loosen bevel lock knob.

0

45

BEVEL

LOCK KNOB

 

 

 

 

45

 

 

 

 

 

30

 

 

 

 

 

2.5

 

 

 

 

 

2

 

 

 

 

 

15

 

 

45

30

 

 

 

 

31.62

22.5

15

 

 

 

 

 

BLADE

 

COMBINATION

 

MITER

MITER

SQUARE

 

FENCE

TABLE

 

 

MITER

 

 

 

 

 

 

 

 

 

 

LOCK PLATE

MITER

 

 

 

 

LOCK HANDLE

 

CORRECT VIEW OF BLADE

 

 

SQUARE WITH MITER TABLE

Fig. 25

0

45

 

 

 

 

45

 

 

 

 

30

 

 

 

 

5

 

 

 

 

2.

 

 

 

 

2

 

 

 

 

15

 

45

30

 

15

 

31.62

22.5

 

 

 

 

BLADE

MITER

COMBINATION

MITER

SQUARE

FENCE

TABLE

 

 

 

 

 

 

 

 

VIEW OF BLADE NOT SQUARE WITH MITER

 

TABLE, ADJUSTMENTS ARE REQUIRED Fig. 26

 

0

 

 

 

 

45

 

 

 

 

 

 

 

45

 

 

 

 

30

 

 

 

 

2.5

 

 

 

 

2

 

 

 

 

15

 

45

30

 

15

 

31.62

22.5

 

 

 

 

BLADE

MITER

COMBINATION

FENCE

MITER

SQUARE

 

TABLE

 

 

 

VIEW OF BLADE NOT SQUARE WITH MITER

TABLE, ADJUSTMENTS ARE REQUIRED

Fig. 27

■Adjust positive stop adjustment screw to bring saw blade into alignment with the square. See Figure 28.

■Retighten bevel lock knob. Next, retighten lock nut se- curing the positive stop adjustment screw. Recheck blade-to-table alignment.

Note: The above procedure can be used to check blade squareness of the saw blade to the miter table at both 0° and 45° angles.

Your saw has two scale indicators, one on the bevel scale and one on the miter scale. After squaring adjustments have been made, it may be necessary to loosen the indicators screws and reset them to zero. See Figure 24.

Page 18

Page 17 Page 19
Page 18
Image 18
Ryobi TS1351 manual Squaring the Blade to the Miter Table, See Figures 25
Page 17 Page 19

TS1351 specifications

The Ryobi TS1351 is a versatile and robust table saw designed to meet the needs of both DIY enthusiasts and professional woodworkers. Known for its impressive performance and user-friendly features, the TS1351 stands out in its category, making it an ideal choice for those looking to enhance their woodworking capabilities.

One of the key features of the Ryobi TS1351 is its powerful 15 Amp motor, which delivers ample cutting power for a variety of tasks. This motor enables users to cut through hardwoods, softwoods, and even engineered materials with ease. The saw offers a maximum cutting depth of 3-1/8 inches at 90 degrees, allowing for substantial cuts in thicker materials.

The TS1351 is equipped with a 10-inch carbide-tipped blade that provides a fine finish and extended blade life. The blade can be adjusted for height and angle, allowing for precise bevel cuts of up to 45 degrees. This versatility makes it possible to perform a wide range of cuts, including crosscuts, rip cuts, and miter cuts, making the saw suitable for diverse woodworking projects.

Safety is a priority with the Ryobi TS1351. It features a blade guard and an anti-kickback pawl, which help protect users during operation. The push stick, included with the saw, further enhances safety by allowing operators to make cuts without putting their hands near the blade. Additionally, the sturdy base offers stability, reducing vibrations and ensuring accurate cuts.

Another innovative characteristic of the TS1351 is its portability. Weighing in at just over 50 pounds, the saw is easy to transport, making it suitable for job sites or home workshops. The onboard storage for accessories also helps keep the workspace organized and reduces setup time.

The Ryobi TS1351 further enhances user experience with its quick-release guard, easy-to-read scales, and a large table surface that provides ample room for material support. Whether tackling small projects or larger builds, this table saw delivers reliable performance, precision, and safety, making it a valuable tool for any woodworker or craftsperson.