ASSEMBLY
TABLE EXTENSIONS
See Figures 11, 12, and 13.
If you plan to use the stop block, slide the stop block on the back arm of the desired table extension first.
To install table extensions, insert the ends of extensions into the holes in the sides of the base. See Figures 12 and 13. Adjust the extensions to the desired length.
Secure them in place by positioning a clamp bracket under each table extension beneath the miter table. Orient each clamp bracket as shown in figure 13.
Secure each clamp bracket in place with a clamp bracket screw. The clamp bracket screw threads through the clamp bracket and tightens against bracket support on bottom of miter table, securing clamp bracket against table extension.
STOP BLOCK
See Figures 11 and 14.
The stop block is included with the table extensions and is useful as a stop for making repetitive cuts to the same length. It can be installed on either side of the saw base:
Slide the stop block on the back arm of either table extension, then insert the table extensions into the saw base.
Use the small wing screw to secure the stop block to the table extensions.
Loosen the small wing screw and adjust the stop block the desired distance from the blade for the cut to be made. For accurate placement of the stop block, mea- sure the distance from the teeth set on the blade to the stop block.
Tighten wing screw securely.
Plug the saw in.
Make a test cut in scrap material and measure the length of the workpiece.
Make any necessary adjustments.
WARNING:
Always make sure your miter saw is securely mounted to a workbench or an appropriate workstand. Failure to do so could result in an accident resulting in possible serious personal injury.
STOP BLOCK
SMALL
WING SCREW
TABLE
EXTENSION
MITER
SAW BASE
Fig. 11
TABLE
EXTENSION
10
|
|
|
| 8 | 9 | 1 2 |
|
|
| 7 | 1 2 |
| |
|
| 6 | 1 2 |
|
| |
| 5 | 1 2 |
|
|
| |
4 | 1 2 |
|
|
|
| |
1 2 |
|
|
|
|
|
3 | 1 2 |
2 | 1 2 |
1 | 1 2 |
5 4
30
5 1
30
MITER | Fig. 12 | |
SAW BASE | ||
SAW VIEWED FROM BOTTOM |
| |
MITER |
| |
SAW BASE | BRACKET | |
| ||
| SUPPORT | |
| CLAMP | |
TABLE | BRACKET | |
ASSEMBLED | ||
EXTENSION | ||
|
CLAMP
BRACKET
CLAMP
BRACKET SCREW
Fig. 13
|
|
|
|
|
|
|
| 9 | 10 |
|
|
|
|
|
|
| 8 | 1 2 | |
|
|
|
|
|
| 7 | 1 2 |
| |
|
|
|
|
| 6 | 1 2 |
|
| |
|
|
|
| 5 | 1 2 |
|
|
| |
|
|
| 4 | 1 2 |
|
|
|
| |
|
| 3 | 1 2 |
|
|
|
|
| |
| 2 | 1 2 |
|
|
|
|
|
| |
1 | 1 2 |
|
|
|
|
|
|
| |
1 2 |
|
|
|
|
|
|
|
|
STOP | 4 |
BLOCK | 5 |
30 | |
| 5 |
| 1 |
| 30 |
Fig. 14
Page 13
