93

DESCALING

 

94

DESCALING

 

In this case, the following message will be displayed:

"DESCALING "

When this message is displayed, the machine does not stop; however, it is suggested to descale quickly the machine.

To cancel the message, see programming menu indications, point 14.

The machine has been adjusted on a 25°òH value, which causes the warning light to switch on after 150 l approx.

Should it be necessary, the water hardness value may be exactly programmed, following the instructions shown at page 82.

Pour a discaling solution into the water tank (according to the instructions on the product package). Switch the machine on the programming mode. Place a large container under the steam/ hot water spout and open slowly the steam knob. The automatic descaling starts: Small amounts of descaling solution are pumped into the circuit. Then the pump stops to let the solution take effect. During this phase, the following message is displayed:

"MACHINE IS

"

"DESCALING

"

After approx. 45 minutes, when the procedure is accomplished, the following message will be displayed:

The following message will be displayed:

 

occurring as a result of the non-observance of

 

 

 

descaling procedures, improper use and non-

"RESET DESCALING

"

observance of any other instruction contained

"NO

 

"

herein. Maintain the manufacturer’s adjustment if

 

 

 

the water hardness degree is not known.

By means of the same keys

, it is possible

Disposal

to modify the value; Yes or no.

 

 

 

 

Machines which are no longer operational

Through this reset operation, the internal counters

should immediately be made non serviceable,

of the two water systems are

reset and

the

by cutting the power cord. Machines should be

message DESCALE is erased.

 

 

 

 

delivered to a public disposal centre.

If the function

 

 

 

 

Switch off and unplug the machine if it will not be

 

 

 

"SIGN. DESCAL.

"

used for long periods.

Cut the supply power cord and deliver the

is selected without the displayed message

machine to a public collecting point.

 

Descale, the following message will be

 

displayed:

 

 

 

The following adjustments are possible: Hardness 4: high water hardness, over 29°òH

"DESCALING "

"FINISHED "

"QUANTITY WATER "

Should the

machine not be used anymore,

switch it off

and unplug it.

(14°dH), i.e. 80 l water approx.

Hardness 3:medium water hardness, approx. 20-29°òH (7-14°dH), approx. 150 l water passage.

Hardness 2:soft water, approx. 12-20°òH (4-7°dH) approx. 300 l water passage Hardness 1:very soft water, less than 10°òH (3°dH), approx. 500 l water passage

In hard water regions, a filter should be used both to improve the coffee quality or to protect the machine, thus reducing the descaling frequency.

Note: for this purpose, use a descaling product suitable for coffee machines.

Never use vinegar!

Descaling can be performed in two ways:

Automatic descaling

Select this mode in the programming menu (see page 84).

By means of keys , move the asterisk at

the end of the line on the menu itemDescaling and confirm the selection with the ENT key. The following message will be displayed:

"13 DESCALING

"

Close the steam knob. The pump stops.

Press ENT button. A display message reminds you to rinse away any possible descaling residues from the machine.

"RINSE MACHINE

"

Remove water tank, rinse it accurately and fill it with fresh water. Clean the machine using the hot water knob and let the whole tank content flow out. The following message will be displayed:

"RINSING "

"FINISHED "

Press the hot water key again. Go back to programming function by pressing theENT key.

Note: By pressing the ESC key, it is possible to quit descaling procedure.

Reset descaling message

In programming function, by pressing keys ,

move the asterisk till the end of the line on the menu Sign. Descal and confirm the selection with ENT button.

"NOT REACHED

"

Standard descaling

Switch off the machine. Pour a descaling solution into the water tank (according to the instructions on the product package). Place a large container under the steam/hot water spout (7). Switch the machine on by pressing the main switch, press the hot water key and let the descaling solution in the water tank pour out of the spout for 1 minute approx.

Press hot water key to complete the operation. Switch the machine off and let the solution taking effect for 5 minutes approx. Repeat this procedu- re two or three times, to empty the water tank.

As soon as descaling has been performed, rinse the water tank (11) thoroughly and fill it with fresh water.

Switch on the machine again and let water (2 l approx.) flow out of the steam/hot water dispensing tube in order to rinse away residues.

Important:

A periodic descaling ensures a correct machine functioning and avoids expensive repairs. The machine warranty does not cover damages

Keep the machine in a dry place, far from the reach of children.

Should the machine not be used for a long period, keep it from dust and dirt

Maintenance

Periodically check the machine working and clean it in accordance to the instructions.

Troubleshooting

In case of failure, fault or suspected damage following a fall, unplug the machine immediately.

To fix problems, follow the instructions in the table. Otherwise contact authorised personnel. Only skilled personnel are authorised to repair the machine. The user might incur serious injuries should repairs not be properly carried out.

The manufacturer declines any liability whatsoever, should repairs fail to be carried out according to the instructions contained in this manual: Furthermore in these cases warranty rights cannot be honored.

Page 13
Image 13
Saeco Coffee Makers SUP 016 manual Machine is Descaling, SIGN. Descal, Descaling Finished Quantity Water, Rinsing Finished