Saeco Coffee Makers SUP 016 manual Please Activade, Water Hardn, Select Product, Ready For Use

81 DRAINAGE

82 PROGRAMMING THE MACHINE

31

Install the water tank, slightly pressing over it to fit the valve which will open automatically.

Do not fill the tank with an excessive quantity of water.

Always fill the tank with fresh water only: hot water as well as other fluids might damage the tank. Never use carbon dioxide added water.

Important: It is advisable to drain the machine before the first start, after a prolonged period the machine has not been used or whenever the water tank has been completely emptied.

Furthermore, should the pump be defective, the display shows:

"VENTILATE "

Programming the machine

32

To enter the programming mode, press the key ENT ( pre-ground coffee) when the machine is on and keep it pressed until the first two lines of the programming mode are displayed:

keys . The keyENTallows you to activate the selected item. It is possible to modify the selected

figuresinamenuitemusingthekeys .Thekey

ENT memorizes the selected options (for instance “ON” for the cup heating plate).

Should you accidentally change some data, press ESC (*…) to leave the menu item without saving the new options which were selected accidentally.

Language selection

Move the asterisk to the menu item

“LANGUAGE” using the keys . Press

ENT to activate this item. The following message will be displayed:

"PLEASE ACTIVADE	"
"SYSTEM 2	"

Water hardness adjustment

In order to adjust the water hardness, it is necessary to test the water using the strip supplied with the machine. Dip the strip into the water for a second, shake off excess water gently, wait approx. 1 minute and read the results.

Move the asterisk at the end of the line to the menu item “WATER HARDN.” using the keys

and select it by means of the ENT

button.

The following message will be displayed:

Do not switch on the machine on if the water tank is empty: always make sure there is enough water in the tank!

Connect the plug to the socket and press the main switch. The following message will be displayed:

"WARMING UP "

Should

"1	LANGUAGE	"
"2 SYSTEM 2		"

At the end of the line a blinking asterisk is displayed, which can be moved up and down

with the keys (tall and regular coffee). If the asterisk is on the first menu, press button

to move it on the second menu and vice versa. The display shows the following sequence of messages:

"1 LANGUAGE	"
"ENGLISH	"

The keys allow you to change the set options : “ENGLISH” , “ITALIANO” , “FRANÇAIS”,

“DEUTSCH” ,“NEERLANDAIS”,“ESPAÑOL”, “PORTUGUES”.

Enabling of second heating system Royal Cappuccino is equipped with two boilers

"3 WATER HARDN./	"
"HARDNESS 3	"

The keys allow you to change the set options:

HARDNESS 4

(hard water)

HARDNESS 3

(medium water)

Hardness 4

"ENERGY		"	1	LANGUAGE	10 PROG. H. WATER
"SAVING		"
			2	SYSTEM 2	11 PROG. CAPPUC.
be displayed, press button	“Standby”	to	3	WATER HARDN.	12 TOTAL COFFEE
			4	CUP HEATER	13 DESCALING
disactivate the energy saving mode.
			5	TEMP. L. COFFEE	14 SIGN. DESCAL.
			6	TEMP. COFFEE	15 TIMER

with independent circuits. One of these boilers can be disconnected. By pressing

keys move the asterisk at the end of the

line to the menu item “SYSTEM 2”. Press ENT to activate this item. The following message will be displayed:

Hardness 3	HARDNESS 2
	(soft water)
Hardness 2	HARDNESS 1
Hardness 1	(very soft water)

Drainage	7	TEMP. S. COFFEE	16 VENDING
Direct the steam/hot water spout on the drip tray	8	PREBREWING	17 EXIT
	9	PREGRINDING
(2). Place a cup or another suitable container
under the dispensing tube, then turn the steam/

"2 SYSTEM 2	"	Cup heating plate connection
		Royal Cappuccino is equipped with a useful cup
"ON	"	heating plate which can be disconnected, if
		required.

hot water knob counterclockwise. The pump			To leave the menu, move the asterisk at the end
			of the line to item <<Exit>> using the key	.
starts automatically. Wait until a regular water jet
is obtained, then close the knob. The machine is Then, press ENT ( pre-ground coffee). The
now drained and ready to work.			machine is now in the normal mode again.
The following message will be displayed:			Selecting single menus
	"SELECT PRODUCT	"	Select the different menu items by means of the
	"READY FOR USE	"

The keys allow you to change the set

options: ON, OFF.

If the second boiler is disconnected it is not possible to dispense steam and therefore cap- puccino can’t be prepared. Should the cappuc- cino selection button be pressed

or the steam/hot water knob be opened, the display shows the following message:

Press keys to move the asterisk to item

“CUP HEATER”. Press ENT to activate this function.

The following message will be displayed:

"4 CUP HEATER	"
"ON	"