![](/images/new-backgrounds/1151593/1515935x1.webp)
Cyborg Evo Force Manual EFGIS.qxd 15/07/2004 12:38 Page 4
IMPORTANT NOTICE
This product uses a dynamic
REMARQUE IMPORTANTE
Ce produit utilise un système dynamique
WICHTIGE INFORMATION
Für eine präzise Kontrolle im Spiel verwendet dieser Saitek Joystick ein dynamisches
IMPORTANTE
Questo prodotto utilizza un sistema dinamico di calibrazione automatica, progettato per consentirvi un controllo più accurato dei vostri simulatori di volo favoriti con il vostro Joystick Saitek. Per massimizzare l'efficacia di questa funzione, è necessario muovere il joystick completamente in avanti, indietro, a destra e a sinistra dopo avere avviato il PC e prima di caricare il vostro gioco.
AVISO IMPORTANTE
Este producto usa un sistema dinamico de auto calibración para un mejor control del joystick en los juegos de simulación. Para maximizar la efectividad del sistema es necesario mover el joystick TOTALMENTE adelante, atras a izquierda y a derecha al encender el ordenador y antes de cargar el juego.
GETTING STARTED
In order for this product to function correctly please install the drivers on the CD supplied with this product. The force effects of this joystick will not work unless the correct drivers have been installed.
INSTALLATION FOR USERS OF WINDOWS® XP
A) Drivers Only For Typical Users
1With your computer switched on, close down any programs that are currently running and insert the Saitek Smart Technology CD into your
2When the Introduction Screen appears, click Install Software to continue. If the CD does not run automatically, select Start from the Windows® Taskbar, then Run and type D:\Setup.exe and click OK - where D:\ is the letter of your
3When the Welcome screen appears, click Next to continue.
4After reading the Disclaimer, select the I accept the terms of the Disclaimer option and click Next to continue.
5At the Driver Setup screen, if you haven’t already done so, plug in your controller and click on Next.
6At the Driver Setup screen, click Next to test your controller.
7When the Saitek Controller screen appears, try out all your controller’s buttons, controls and forces to show that it is working properly. When you have finished, click OK.
8At the Software Setup screen, select Do not install the SST Programming Software and click Next. The Programming Software can be installed at a later date by following instruction (B). below
9At the Registration screen, select Check this box to register now and follow the
10Click on Finish to complete the installation.
B) Drivers and Programming Software For Advanced Users
1Follow points 1 – 7 of the install procedure in A), then at the Software Setup screen, select Install the SST Programming Software and click Next.
2In the following Software Setup screen, click Next and follow the
3At the Registration screen, select Check this box to register now and follow the
4Upon completion of the installation, you have the option to Run Profile Editor, which will give you a view of the 3D programming environment. If you do not wish to see the Profile Editor at this point, just uncheck the box and click on Finish to complete the installation.
INSTALLATION FOR USERS OF WINDOWS® 2000
A) Drivers Only For Typical Users
1With your computer switched on, close down any programs that are currently running and insert the Saitek Smart Technology CD into your
2When the Introduction Screen appears, click Install Software to continue. If the CD does not run automatically, select Start from the Windows® Taskbar, then Run and type D:\Setup.exe and click OK - where D:\ is letter of your
3When the Welcome screen appears, click Next to continue.
4After reading the Disclaimer, select the I accept the terms of the Disclaimer option and click Next to continue.
5At the Device Driver Installation screen, click on Next and follow the
6When prompted, plug your controller’s USB connector into your computer, then click on Configure.
7When the Controller Properties screen appears, click Next to view the Test screen.
8Now try out all your controller’s buttons, controls and forces to show that it is working properly. When you have finished, click OK.