Controls and Functions
FRONT PANEL CONTROLS
MAIN SECTION
The PA 324 has two internal power amplifiers and depending on the POWER AMP selection switch, the amplifiers are sent the MAIN or MONITOR bus sig- nal. The following section describes the MAIN bus operation, which allows you to adjust the
SAMSON |
|
| PA324 |
| |||
|
| 24BITDSP |
| ||||
POWERED MIXER |
|
| DIGITAL EFFECTS |
| |||
|
|
|
|
| |||
| MONITOR |
|
|
|
|
|
|
| 18 |
|
|
| POWER |
|
|
|
|
|
|
|
|
| |
| +3 +6 | CLIP PHANTOM |
|
| |||
|
|
|
|
|
| MODE |
|
|
|
|
|
| ON BRIDGE | MAIN | |
| MAIN |
|
|
| OFF | MAIN | MAIN |
|
|
|
|
| MAIN | MONITOR | |
|
|
|
|
|
| ||
|
|
| MONITOR / MAIN |
|
|
| |
EFX | +12dB |
|
|
| +12dB |
| |
| 5 |
|
|
|
| 5 |
|
| 0dB |
|
|
| 0dB |
|
|
0 | 10 |
|
|
|
| 0 | 10 |
RETURN |
|
|
|
| VOLUME |
| |
|
|
|
|
| |||
| 63Hz | 160Hz | 400Hz | 1KHz 2.5KHz | 6.4KHz 16KHz |
|
|
| 15 |
|
| MAIN |
|
|
|
|
|
|
|
|
|
| |
EFX | +12dB |
|
|
| +12dB |
| |
| 5 |
|
|
|
| 5 | 17 |
| 0dB |
|
|
| 0dB |
|
15 | Graphic Equalizer | 0 | 10 |
|
|
| 0 | 10 |
16 | RETURN | 400Hz 1KHz | 2.5KHz | 6.4KHz 16KHz | VOLUME | |||
| The PA324’s |
|
|
|
|
|
|
|
| you to contour the frequency response of the |
|
|
|
|
|
|
|
| MAIN mix bus signal, providing a maximum of |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| This is an especially useful tool for cutting fre- |
|
| 1 | 1 |
|
|
|
| quencies that cause annoying feedback. The |
|
|
|
|
|
|
|
| frequency response is flat when a slider are in |
|
| 2 | 2 |
|
|
|
| the center position. Moving a slider in the posi- |
|
|
|
|
|
|
|
| tive direction will boost that frequency by as |
| AUX IN | TAPE IN | REC OUT | MAIN OUT | MONITOR OUT | |
| much as 12dB, and moving the slider in the |
| ||||||
|
|
|
|
|
|
|
| |
| negative direction will cut that frequency by up |
|
|
|
|
|
|
|
| to 12dB. Once you set a response curve using the Graphic Equalizer, the EQ curve is applied to both the | |||||||
| MAIN bus signal that is output to the speakers, and the line level signal which is output from the MAIN OUT | |||||||
| jack. |
|
|
|
|
|
|
|
16Effects Return Control (EFX RETURN)
The EFX RETURN control is used to adjust the level of the effect sound being sent back from the
17Volume Control (MASTER)
The MASTER MAIN level control is the
18Output Level Meter
The OUTPUT LEVEL METER allows you to monitor the level of the signal which is being sent to the MAIN OUT jack (input/output panel 5).
NOTE: To avoid distortion, adjust the MASTER LEVEL control so that the 0 indicator LED lights occasionally.
8