Controls and Functions
FRONT PANEL CONTROLS
POWER AMP SECTION
The PA324’s power amplifier section can |
|
|
|
|
|
|
|
|
|
| PA324 |
| ||||||||||
|
|
|
|
|
|
|
|
|
| 24BITDSP | ||||||||||||
be configured to operate several ways |
|
|
|
|
|
|
|
|
|
| ||||||||||||
depending on whether you need MAIN plus |
|
|
|
|
|
|
|
|
|
| DIGITAL EFFECTS | |||||||||||
MONITOR amplifiers to power your speak- |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ers, or if you just need more power for the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MAIN speakers. The section below |
|
|
|
|
|
|
|
|
|
|
| POWER |
|
| 19 |
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
describes the PA324 power amp modes. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
| CLIP PHANTOM |
|
|
|
|
|
|
| |||||||||||||
|
|
| MODE | |||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
19 Mode |
|
|
|
|
|
|
|
|
|
|
|
|
| ON BRIDGE |
|
|
|
| MAIN | |||
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| OFF | MAIN |
|
|
|
| MAIN | |||
The MODE switch is used to select one of |
|
|
|
|
|
|
|
|
|
|
|
|
| MAIN |
|
|
|
| MONITOR | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
three different operating modes, MAIN- | N |
|
|
|
|
|
|
| ||||||||||||||
MONITOR, |
|
|
|
|
|
|
|
|
|
|
|
|
|
| +12dB |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
BRIDGE. The following is a description of |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 5 |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
each of the POWER operating modes: |
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0dB |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 | 10 |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CAUTION! Only change the power amp mode switch when the PA324’s power is SWITCHED OFF!
With this setting, the MAIN and MONITOR sections can be used independently. The MAIN bus signal will be sent from the POWER AMP 1 A/B jacks, and the MONITOR bus signal will be sent from the POWER AMP 2 A/B jacks.
With this setting, the two power amp channels can be used independently. The MAIN bus signal will be output from the POWER AMP 1 A/B jacks (Rear Panel 1), and also, from the POWER AMP 2 A/B jacks (Rear Panel 1).
With this setting, the two power amp channels (A and B) will be connected in bridge mode. Only the MAIN bus signal will be output from the BRIDGE jack.
9