Connecting the SUB120
Mono Sub With Passive Satellites Using Line Inputs
The SUB120 can be operated using line level inputs and outputs. When using the SUB120 at line level, the full range signal is maintained at the outputs. Below is a typical system set up using the SUB120 with a mixer, stereo power amp and a pair of passive satellite loudspeakers. The SUB120’s inputs and outputs utilize industry stan- dard RCA connectors. For a detailed wiring diagram, see the section SUB120 Connections on page 17. Follow the steps below the diagram to set up your system.
| – | + |
|
|
| – | + |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| INPUT |
|
|
| INPUT |
| ||||||
AMPLIFIER
PUSH TO RESET
20A / 250V
~AC INPUT 115V / 60Hz, 800W
POWER | 115V - 60Hz 800W | SERIAL NUMBER |
RATING |
| |
| CAUTION |
|
| RISK OF ELECTRIC SHOCK |
|
| DO NOT OPEN. |
|
|
| MADE IN KOREA |
OUTPUT
CHANNEL 2 | CHANNEL 1 | ||
MINIMUM LOAD IMPEDANCE | + | - | |
STEREO - | + | ||
(4Ω/CHANNEL) |
|
|
|
BRIDGED MONO | - | + |
|
(8Ω) |
| ||
AVIS ; RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
SAMSON
CAUTION
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICEABEL PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE TO RAIN OR MOISTURE.
CAUTION ; REPLACE WITH THE SAME TYPE FUSE AS INDICATED.
UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE.
INPUTS
| TIP RING SLEEVE | TIP RING SLEEVE |
| ||
| TIP | + | TIP | + |
|
CHANNEL 2 | RING | - | RING | - | CHANNEL 1 |
SLEEVE GND | SLEEVE GND | ||||
|
| MODE SELECTOR |
|
| |
INPUT | BRIDGED | STEREO | INPUT | ||
(10KΩ / 0dBu) |
|
| (10KΩ | / 0dBu) | |
www.samsontech.com
FROM MIXER
|
|
|
|
|
|
|
| FROM EXTERNAL AMPLIFIER | |||||
|
|
|
|
|
|
|
|
| SPEAKER OUTPUT |
| |||
|
| POWER |
| AUTO ON | PREAMP LEVEL | + | R | - | - | L | + | ||
| 5 | 70 | ON | OFF 0° 180° | INPUT | OUTPUT |
|
|
|
|
|
| |
|
| PEAK |
|
| R |
|
| R |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| PHASE |
|
|
|
|
|
|
|
|
0 | 10 |
| 40 | 180 | L |
|
| L |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
VOLUME |
| SWEEP Hz |
|
|
| + | R | - | - | L | + | ||
|
|
|
|
|
|
|
| TO PASSIVE SATELLITE SPEAKERS | |||||
SUB120 120 WATT 10" SUBWOOFER
•Lower your mixer’s master outputs to all the way off.
•Connect the mixer’s left output to the SUB120’s LEFT PREAMP LEVEL INPUT and the mixer’s right out- put to the SUB120’s RIGHT PREAMP LEVEL INPUT. Now connect the SUB120’s LEFT PREAMP LEVEL OUTPUT to the left side input of the power amp, and the SUB120’s RIGHT PREAMP LEVEL OUTPUT to the right side input of the power amp. Connect a speaker wire from the left output of your power amp to your left satellite, and then, connect a speaker wire from the right output of your power amp to your right satellite.
•Now adjust the SWEEP control to the desired frequency. Consult your studio monitors owner’s manual for a recommended crossover point. You can also use your ears by adjusting the SWEEP control to the frequency that sounds good to you. A good place to start is about 70 Hz.
•Now set the level of your power amp up to the normal operating level. Run an audio signal (like some music from a CD) through your mixer and raise the level to a comfortable listening level. Now slowly raise the SUB120 volume control and listen to the low frequency output. Adjust the SUB120 to the level of low frequency output that you like. Now, when you raise and lower your mixer’s output, the SUB120 and satellites will track at the same relative volume.
12
