Samsung CHT-350 instruction manual Advanced Connections are covered in Appendix a

Using the TV Buttons on the Remote Control

Basic Connections/Auto Setup

POWER				TV POWER
			1
OPEN/CLOSC				MUTE
EJECT
	1	2	3		5
SPEAKER				SOUND
				MODE
	4	5	6
REPEAT		100+	0	ZOOM	STEP
		ANGLE		ATR
3	TV VOL.		CH/TRK	AMP VOL.
		TV		TV INPUT

SELECT 2

3

DVD VCR FM/AM INPUT

REPEAT 100+	0	ZOOM	STEP
ANGLE		ATR
TV VOL.	CH/TRK		AMP VOL.
4
TV		TV INPUT

SELECT

DVD 4 FM/AM INPUT

Your VCR remote control will work with Samsung televisions and compatible brands.

To determine whether your television is compatible, follow the instructions below.

1Switch your television on.

2Point the remote control towards the television.

3Hold down the TV button and enter the two-figure code corresponding to the brand of your television, by pressing the appropriate numeric buttons.

Brand	Codes	Brand	Codes
SAMSUNG	01, 14, 15, 23	LOEWE	28
SHARP	02, 16, 22	ZENITH	17
SONY	03	LG	06, 08, 18
RCA	07, 29	MAGNAVOX	04
TOSHIBA	09	EMERSON	21
PANASONIC	12, 24	SANYO	05, 20
JVC	11	DAEWOO	19
HITACHI	10	NOBLEX	25
MITSUBISHI	13	TELEFUNKEN 26
NEWSAN	27

Result: If your television is compatible with the remote control, it will switch off. It is now programmed to operate with the remote control.

➢ If several codes are indicated for your television brand, try

each one in turn until you find one that works.

☛ When you change the batteries in the remote control, you

must reprogram the code, following the same procedure.

In this section, you will connect the DVD-VCR to your television and run Auto Setup, which automatically searches for channels and sets the player’s internal clock.

NOTES:

•Advanced Connections are covered in Appendix A.

•Even if you plan to use the S-Video or Component Video Outputs, you MUST connect the DVD-VCR to your television with

either the standard RF or the Line Out connection. This enables you to operate the DVD-VCR setup menus.

1 Connect Antenna/Cable to DVD-VCR

Connect the RF antenna cable from your indoor/outdoor antenna or

cable wall outlet to the IN (FROM ANT.) jack on the back panel of

the DVD-VCR.

2 Connect DVD-VCR to TV

Choose one of the following methods to connect the DVD-VCR to

your TV:

RF Connection

Connect the supplied RF antenna cable from the OUT (TO TV) jack

on the back panel of the DVD-VCR to your television’s Antenna

Input.

NOTE : Check the channel to connect DVD-VCR to your

television’s Antenna Input; See page 22.

Line Connection

Connect an RCA-type audio/video cable (red, white, yellow) from

the LINE OUT jacks on the back panel of the DVD–VCR to your

television’s Line In jacks. Use red for right audio, white for left

audio, and yellow for video.

NOTE: It is recommended that you use the Line Connection if your

TV is equipped with RCA jacks.

3 Plug In DVD-VCR

Connect the DVD-VCR power cord to a standard wall outlet. Don’t

press any buttons on the DVD-VCR or remote during auto setup.

“AUTO” blinks while the DVD-VCR runs an auto setup procedure,

RIDIO ANT.	IN
(FROM ANT.)
FM
75
COAXAL
		DVD & VCR
RF	OUT	LINE IN 1		LINE IN 3
		1
AM	(TO TV)
		VIDEO L - AUDIO - R	VIDEO	L - AUDIO
		LINE IN 2		LINE OUT
From Antenna or Cable

RIDIO ANT.	IN
(FROM ANT.)
FM
75
COAXAL
		DVD & VCR
RF	OUT	LINE IN 1	LINE IN 3
		2
AM	(TO TV)
		VIDEO L - AUDIO - R	VIDEO L - AUDIO - R
		LINE IN 2	LINE OUT
		2
To TV’s Antenna Input

You can then control the television using the following buttons.

Button	Function
POWER ➀	Used to switch the television on and off.
INPUT ➁	Used to select an external source.
VOL + or – ➂	Used to adjust the volume of the television.
CH (or ❷) ➃	Used to select the required channel.
MUTE ➄	Used to toggle the sound on and off.

➢The various functions will not necessarily work on all televisions. If you encounter problems, operate the television directly.

	where it will automatically search for all active channels and set the
	clock. When Auto setting has been completed, the front panel
	displays the current time. If Auto Clock set is unable to find a
	channel to set the clock, you can set the clock manually; See page
	18.
4	Turn On DVD-VCR
	Press the POWER button on the remote control or on the
	DVD–VCR’s front panel.
5	Turn On TV
	Press the POWER button on your TV.
6	Set TV to Channel 3, 4 or Line
	Be sure to use the same channel you selected in Step 2. If you
	used the Line Connection, set your TV to its Line Input.

PHONES

4

POWER			TV POWER
OPEN/CLOSC		4		MUTE
EJECT
SPEAKER	1	2	3	SOUND
				MODE
TEST	4	5	6	SOUND
				EFFECT
MODE	7	8	9	DIGEST
REPEAT	100+	0	ZOOM	STEP
	ANGLE		ATR

12

13