Samsung DVD-R100 Step3 : Connecting the Video cable

English -

Method 3 : Connecting to

Component video input

jacks(Y,Pb,Pr) in 480i mode

1. Connect Component video cables(not supplied)

between the COMPONENT VIDEO OUT jacks on

DVD Recorder and COMPONENT VIDEO IN jacks

on the TV (or AV amplifier).

2. Set the Component video out select switch on the

back of your DVD recorder to 480i video output

mode. Make sure that the disc has stopped complete-

ly before changing the switch position.

●

You will enjoy high guality accurate color reproduc-

tion images. Component video separates the picture

element into black and White(Y), blue(Pb), red(Pr)

signals to present most clear and clean images.

Method 2 : Connecting to an S-

video input jack

Connect an S-video cable(not supplied) between the S-

VIDEO OUT jack on DVD Recorder and S-VIDEO IN

jack on the TV (or AV amplifier).

●

You will enjoy high quality images. S-Video separates

the picture element into black and white (Y) and color

video input mode.

COMPONENT

■

If you change the component video out-

put switch when the power is off, the

startup screen may not be displayed nor-

mally.

■

Make sure that the color coded connec-

tions match. The Y, Pb, Pr component

output jacks of your DVD Recorder must

be connected to the exact corresponding

component input jacks on your TV.

Otherwise, red or blue images will be dis-

played on the TV screen.

■

Make sure that the left and right audio

output jacks of your DVD Recorder are

connected to the left and right audio input

jacks of your TV, respectively. (See page

18)

NOTE

- English

scan video output jack is used in progressive output

mode. This is only available with TVs that support

progressive scan.

●

Progressive Scan Output (525p)

“Consumers should note that not all high definition

television sets are fully compatible with this product

and may cause artifacts to be displayed in the picture,

in case of 525 progressive scan pictrue problems, it is

recommended that the user switch the connection to

the ‘standard definition’ output. If there are questions

regarding our TV set compatibility with this model

525p DVD player, please contact our customer service

center at 1-800-SAMSUNG.

●

The VHF/UHF RF OUT jack of this product sends

only signals received through the antenna. It does not

output audio/video signals.

You must use one of the following audio/video

connections on this unit.

Method 1 : Connecting to a Video

input jack

Connect a video(yellow) cable between the VIDEO(yel-

low) OUT jack on DVD Recorder and VIDEO(yellow)

IN jack on the TV (or AV amplifier).

●

Method 3 : Antenna + DVD

Recorder + Cable box +TV : Cable

box with a few scrambled channels

You can record non-scrambled channels by selecting the

channel on the cable box. You cannot record scrambled

channels that require a cable box.

There are several ways to connect your DVD Recorder.

Select one of the following video connecting that best

suits you below.

●

Method 1 : Connecting to a Video input jack

●

Method 2 : Connecting to an S-video input jack

●

Method 3 : Connecting to Component video input

jacks in 480i mode

●

Method 4 : Connecting to Component video input

jacks in 480p mode

S-Video, Component video and Progressive

Output Modes

●

S-Video and Component video output are available

only if your TV supports S-Video input or Component

video input, respectively. If S-Video or Component

video output does not work, check the TV connec-

tions and the TV input selection settings. (For infor-

mation on how to connect to a TV, see pages 17 to

18.)

●

Compared to standard interlaced video, progressive

scan doubles the amount of video beam lines fed to

your TV, resulting in a more stable, flicker-free, and

clear image than interlaced video. The progressive

Step3 : Connecting the Video

cable

Connecting & Setting UP