Memorizing the Channels | Samsung HCM653WB, HCM4715W, HCM553WB

O P E R AT I O N

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH and CH but- tons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system).

1

Press the Menu button.

Press the CH button to select “Channel”, then press the VOL + button.


						Channel

				Antenna		: A
				ANT/CATV		: ANT
				Auto Program
				Fav. Channel
				Fine Tune		: 00
				Add/Erase
				Labeling		: - - - -

2

Press the CH button to select “ANT/CATV”, then Press the VOL + or VOL - button to cycle through these choices:

ANT (antenna), STD, HRC or IRC (all cable TV).


						Channel
				Antenna		: A
				Antenna		: A
				ANT/CATV		: ANT
				Auto Program
				Fav. Channel
				Fine Tune		: 00
				Add/Erase
				Labeling		: - - - -

Note: STD, HRC and IRC identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area.

At this point the signal source has been selected. Proceed to “Storing Channels in Memory” (next page).

3.8 CHAPTER THREE: TV OPERATION

Image 30

Samsung HCM653WB, HCM4715W, HCM553WB, HCM5525WB, HCM474W manual Memorizing the Channels, Selecting the Video Signal-source

Contents

Owner’s Risk of Electric Shock Do not Open Thank You for Choosing Samsung Example Antenna Grounding Safety Installation Your New TVOperation Special Features Troubleshooting List of Features Chapter One Familiarizing Yourself with The TV ´ Video Input jack Using the Component ShelfFront or Side Panel Jacks Audio Input jacks ´ AUDIO-VIDEO Monitor Output jacks Rear Panel JacksAntenna terminals ¨ Audio Input jacks Video Input jacks ´ +100 Remote ControlPower StillMain ¿ S.Mode ± Mode˘ R.surf ¸ P.Mode Connecting VHF and UHF Antennas Antennas with 300-ohm Flat Twin Leads Separate VHF and UHF Antennas Connecting Cable TVAntennas with 75-ohm Round Leads Cable without a Cable Box This terminal might be labeled Connecting to a Cable Box that Descrambles Some ChannelsCable with a Cable box that Descrambles All Channels ANT IN, VHF IN, or simply, Install AT I O N Connecting a VCR Connecting a Camcorder Connecting a Second VCR to Record from the TV Connecting a DVD Player, DTV Set-Top Box 480i, 480p Connecting to Y, PB, PR Connecting a DTV Set-Top Box 480p Installing Batteries in the Remote Control Install two AAA size batteries Replace the coverMake sure to match the + Press the Power button Plug & Play FeatureYou can also use the Power button on the front panel Turning the TV On and Off CH or CH button. refer to Setting the clock on 1Press the Menu button Using the Perfect Focus Feature You can also select PerfectFocus by pressing the Perfect Focus button Adjusting Manual Convergence Adjust Red Convergence If a horizontal red line is visible, use Viewing the Menus and On-Screen Displays Viewing the MenusViewing the Display Selecting a Menu Language Selecting the Antenna Input Selecting the Video Signal-source Memorizing the Channels Storing Channels in Memory Automatic Method TV automatically cyclesAdding and Erasing Channels Manual Method Using the Previous Channel Using the Channel ButtonsUsing the Number Buttons Changing Channels Can be set as Favorite channels Selecting Your Favorite ChannelsTo Store Your Favorite Channels To View Your Favorite Channels Adding and Erasing Channels Manual Method Press CH or CH to tune to the channel that will be labeled Labeling in the A/V modeLabeling the Channels Select Channel, then Customizing the Picture After adjusting an item,Picture Control Gauge will automatically disappearafter about 4 seconds Using Automatic Picture Settings Press the Menu button. Picture icon will be high- lighted Sound Control Adjusting the VolumeUsing Mute Selecting the Color Tone Customizing the Sound Press the Menu button exit Using Automatic Sound Settings When selecting the hours, be Setting the ClockOption 1 Setting the Clock Manually Sure to select the proper time of day AM or PM Press the Menu Press the VOL + button to select Auto clock set On Press the CH button to select Time Zone Press the VOL + or VOL button to adjust the fine tuning Fine Tuning ChannelsAfter you adjust the fine tuning Star icon*will appear Digital Noise Reduction Wide TV Changing the Screen Size43 TV Press the Aspect button to change the screen Using the R.surf feature Setting the On/Off Timer Before using the timer, you mustSelect Function, then Select Off during this step Setting the Sleep TimerTo deactivate the On time If no function buttons Extra sound settings Surround, Auto Volume, Melody, BBE Surround Quick way to access the MTS Choosing a Multi-Channel Sound MTS Soundtrack Select Mode, then press Viewing Closed CaptionsDifferent channels and fields Select Caption or Text Viewing Picture-in-Picture Quick way to access the PIPMenu Simply press the PIP button on the remote control Activating Picture-in-Picture Quick way to access the signal Selecting a Signal Source Antenna or Cable for PIPSelecting a Signal Source External A/V for PIP Select PIP, then press Swapping the Contents of the PIP Image and Main Image Changing the Size of the PIP Window Changing the PIP Channel Simply press the PIP CH button on the remote controlChanging the Location Rotating in PIP mode Scanning the Available Channels Quick way to access the V-Chip Using the V-ChipSetting Up Your Personal ID Number PIN Menu Simply press the V.Chip button on the remote control How to Enable/Disable the V-Chip How to Set up Restrictions Using the TV guidelines Parent Guidance TV Guidelines screen will appearGeneral audience TV-14 Or CH Mpaa rating screen will appear Highlighted blinking Viewing the DemonstrationPicture icon will be Select Demonstration Remote control has four Customizing Your Remote ControlSetting Up Your Remote Control to Operate Your VCR or DVD Make sure you enter 3 digits Setting Up Your Remote Control to Operate Your Cable Box Codes VCR CodesCable Box DVD Codes Identifying Problems Chapter Five Cleaning and Maintaining Your TV Using Your TV in Another CountrySpecifications