Searching for and Storing Radio Stations
GB | You can store up to: |
|
30 FM stations
1Switch the system on by pressing ( ).
2To listen to the Radio.
Remote Control
a Press the TUNER button.
b. Tune in to the desired station.
Automatic Tuning 1: When the or button is pressed,stations you have preset are selected.
Automatic Tuning 2: Press and hold the or
button to automatically search for active broad- casting stations.
Manual Tuning:Briefly press the or but- ton to increase or decrease the frequency incre- mentally.
Main Unit
a Press the Function button to select the TUNER. b Select a broadcast station.
Automatic Tuning 1: Press the STOP( ( ) but-
ton to select<PRESET> and then press the or
button to select a station you’ve preset.
Automatic Tuning 2: Press the STOP( ( ) but- ton to select<MANUAL> and then press and hold the or button to automatically search the station.
Manual Tuning : Press the STOP( ( ) button to select<MANUAL> and then briefly press the
or button to tune in to a lower or higher fre- quency.
3To store(Preset) stations in Memory. a Press the TUNER button.
b Pressing or buttons on the top panel or
or buttons on the remote control to increase or decrease the frequency respec- tively.
To scroll through the frequencies faster when
searching manually, hold down the or buttons.
The automatic search procedure may stop on a frequency that does not correspond to a radio station. If this happens, use the manual search mode.
c Press TUNER MEMORY.
Result: The current station NO is displayed for a few seconds.
dPressing or buttons on the remote con-
trol to assign a program
number .
ePress TUNER MEMORY to store the radio sta- tion.
Result: The current station NO is no longer dis- played and the station is stored.
fTo store any other radio frequencies required,
repeat Steps b to e.
The SET function can be used to assign a new sta- tion to an existing program number.
14
2
1 2,3
2
DEMO/DIMMER
TUNER MEMORY | REPEAT |
SET 3
SET
DNSe EQ
2,3
2,3
Selecting a Stored (preset)Station
You can listen to a stored radio station as follows:
1Switch the system on by pressing ( ) .
2Press the TUNER button on the remote control.
3Select the radio station as follows.
To listen to ... | Press ... |
Stored station or button to select the desired preset section.
2
DEMO/DIMMER
1
SET
DNSe EQ 3
3
Improving Radio Reception
You can improve the quality of radio reception by:
Rotating the FM antenna
If reception from a specific FM radio station is poor, press MONO/ST.
to switch from stereo mode to mono. The quality of the sound will be improved.
TUNER MEMORY
SET
Timer Function
The timer enables you to switch the system on or off at specific times.
Example: You wish to wake up to music every morning.
If you no longer want the system to be switched on or off
automatically, you must cancel the timer.
Before setting the timer, check that the current time is correct.
For each step, you have a few seconds to set the desired option. If you exceed the time, you must start again.
1 Switch the system on by pressing ( | ) . |
2Press TIMER/CLOCK until TIMER is displayed.
3Press SET.
Result: ON TIME is displayed (instead of the equaliz- er symbols) for a few seconds, followed by any
4Set the timer
a Set the hour by pressing or button. b Press SET.
Result: The minutes flash.
c Set the minutes by pressing or button. d Press SET.
Result: OFF TIME is displayed (instead of the equalizer symbols) for a few seconds, fol- lowed by any
5Set the timer
a Set the hour by pressing or button. b Press SET.
Result: The minutes flash.
c Set the minutes by pressing or button. d Press SET.
Result: VOL XX is displayed, where XX corre- sponds to the volume already set.
6Press or button to adjust the volume level and press SET.
Result: The source to be selected is displayed.
7Press or button to select the source to be played when the system switches on.
If you select... | You must also... |
TUNER (radio) a Press SET.
b Select a preset station by
pressing or .
MP3/CD (compact disc) Load a compact disc.
USB connect usb.
8 | Press SET to confirm the timer. |
| |
9 | Press ( | ) to set the system to standby mode. | GB |
| Result: | is displayed to the left of the time, indicat- |
ing that the timer has been set. The system will switch on and off automatically at the required times.
If the timer switch on and off times are identical, the word ERROR is displayed.
DEMO/DIMMER
1,9
TUNER MEMORY | REPEAT |
SET
3,4,5,6,7,8
DNSe EQ
4,5,6,7
4,5,6,7
2
Cancelling the Timer
After having set the timer, it will start automatically as shown by the TIMER indication on the display. If you no longer wish to use the timer, you must cancel it.
You can stop the timer at any time (system on or in standby mode).
To... | Press TIMER ON/OFF... | |
Cancel the timer | Once. |
|
| Result: | is no longer displayed. |
Restart the timer | Twice. |
|
| Result: | is displayed again. |
ON/OFF
15