outlet (connection flange).
Using the tubes and discharge holes on walls with smaller dimensions will cause a diminution of the suction performance and a drastic increase in noise.
Any responsibility in the matter is therefore declined.
!Use a duct of the minimum indispensable length.
!Use a duct with as few elbows as possible (maximum elbow angle: 90°).
!Avoid drastic changes in the duct cross-section.
Filtration version
The aspirated air will be degreased and deodorised before being fed back into the room.
In order to use the hood in this version, you have to install a system of additional filtering based on activated charcoal.
Installation
The minimum distance between the supporting surface for the cooking equipment on the hob and the lowest part of the range hood must be not less than 45cm from electric cookers and 50cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify a greater distance, this must be adhered to.
Electrical connection
The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area, after installation. If it not fitted with a plug (direct mains connection) or if the plug is not located in an accessible area, after installation, apply a double pole switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over- current category III, in accordance with installation instructions.
WARNING!
Before re-connecting the hood circuit to the mains supply and checking the efficient function, always check that the mains cable is correctly assembled.
The hood is provided with a special power cable ; if the cable is damaged, request a new one from Technical Service.
Mounting
Before beginning installation:
•Check that the product purchased is of a suitable size for the chosen installation area.
•Remove the charcoal (*) filter/s if supplied (see also relative paragraph). This/these is/are to be mounted only if you want lo use the hood in the filtering version.
•Check (for transport reasons) that there is no other supplied material inside the hood (e.g. packets with screws (*), guarantees (*), etc.), eventually removing them and keeping them.
Expansion wall plugs are provided to secure the hood to most types of walls/ceilings. However, a qualified technician must verify suitability of the materials in accordance with the type of wall/ceiling. The wall/ceiling must be strong enough to take the weight of the hood.
Do not tile, grout or silicone this appliance to the wall. Surface mounting only.
Maintenance
Cleaning
Clean using ONLY the cloth dampened with neutral liquid detergent. DO NOT CLEAN WITH TOOLS OR INSTRUMENTS. Do not use abrasive products. DO NOT USE
ALCOHOL!
Always wear work gloves for all maintenance operations.
Grease filter
Fig. 10a-20
Traps cooking grease particles.
The grease filter must be cleaned once a month using non aggressive detergents, either by hand or in the dishwasher, which must be set to a low temperature and a short cycle. When washed in a dishwasher, the grease filter may discolor slightly, but this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Charcoal filter (Optional)
Fig. 19
It absorbs unpleasant odors caused by cooking.
The saturation of the charcoal filter occurs after more or less prolonged use, depending on the type of cooking and the regularity of cleaning of the grease filter.
In any case it is necessary to replace the cartridge at least every four months. The charcoal filter may NOT be washed or regenerated.
Circular carbon filter
Apply one on each side as cover to both the shield grids of the motor impeller, then turn clockwise.
For the disassembly, turn counter-clockwise.
Buying charcoal filters
The Charcoal filter can be bought at Samsung Service Website and Service Center. Please refer to the last page of manual.
Replacing lamps
The hood is equipped with a lighting system based on LED technology.
The LEDs guarantee an optimum lighting, a duration up to 10 times as long as the traditional lamps and allow to save 90% electrical energy.
For replacement, contact the technical service.
Operation
T1. Motor ON/OFF
Press the T1 button and the hood will be activated at default speed (Default Speed : Low).
Press again and the hood will return to sleep mode.
T2. Low speed
Press the T2 button and the hood will be activated at Low speed.
T3. Med Speed
Press the T3 button and the hood will be activated at Medium speed.
T4. High Speed
Press the T4 button and the hood will be activated at High speed
T5. Boost speed
Press the BOOST button and the hood will be activated at Maximum speed for 5 minutes.
T6. Timer ON/OFF
Press the Timer button to set the working time.
Press the Timer button for 3 seconds and the Timer function will turn off.
T7. Light ON/OFF
Press the Light button and the lamps will turn on.
Press the Light button again and the lamps will turn off.
T7. SOUND ON/OFF
Press the Light button for 3 seconds. The sound will be turned off. Press the Light button for 3seconds. The sound will be turned on.
Reset filter signals
•Press the T1 button until hearing the sound signal.
•The flashing LED 1 (grease filter) or 2(carbon filter) stops flashing
Charcoal filter signal ON/OFF
•Press the "1" and "2" Button for 3 seconds and the Charcoal filter signal will be activate.
•Press the "1" and "2" Button for 3 seconds, and the charcoal filter signal will be deactivate.
25
