Manuals / Samsung / TV and Video / Flat Panel Television

Samsung PAL60 Pin Configurations, Scart Connector Ext1,Ext2, PC Input Connector 15Pin, 24Pin

Models: PAL60

1 62

Download 62 pages 7.45 Kb

Page 59

Pin Configurations

ENG

SCART Connector (Ext1,Ext2)

➢ Pins 5, 7, 9, 11, 13, 15 and 16 are used for RGB processing and are

	only wired on the EXT1 or EXT2 connector.
Pin	Signal	Pin	Signal

1Audio output R

2Audio input R

3Audio output L

4Audio chassis return

5Video chassis return (RGB blue)

6Audio input L

7RGB blue input (EXT1)

8Switching voltage

9Video chassis return (RGB green)

10 AV-Link (EXT1)

11 RGB green input (EXT1)

12	-
13	Video chassis return (RGB red)
14	-

15RGB red (EXT1) or chroma input

16Blanking signal (RGB switching)

17Video chassis return

18Blanking signal ground

19Video output

20Video or Luminance input

21Screening/chassis return

PC Input Connector (15Pin)

Pin

PC IN

1Red (R)

2Green (G)

3Blue (B)

4Grounding

5Grounding (DDC)

6Red (R) Grounding

7Green (G) Grounding

8Blue (B) Grounding

9Reserved

10Sync Grounding

11Grounding

12Data (DDC)

13Horizontal sync.

14Vertical sync.

15Clock (DDC)

DVI Input Connector
(24Pin)
Pin	Signal
1	T.M.D.S. Data2-
2	T.M.D.S. Data2+
3	T.M.D.S. Data2/4 Shield
4	T.M.D.S. Data4-
5	T.M.D.S. Data4+
6	Clock (DDC)
7	Data (DDC)
8	Not Connected
9	T.M.D.S. Data1-
10	T.M.D.S. Data1+
11	T.M.D.S. Data1/3 Shield
12	T.M.D.S. Data3-
13	T.M.D.S. Data3+
14	+5V Power
15	5V Grounding
16	Hot Plug Detect
17	T.M.D.S. Data0-
18	T.M.D.S. Data0+
19	T.M.D.S. Data0/5 Shield
20	T.M.D.S. Data5-
21	T.M.D.S. Data5+
22	T.M.D.S. Clock Shield
23	T.M.D.S. Clock+
24	T.M.D.S. Clock-
	59

Image 59

Samsung PAL60 manual Pin Configurations, Scart Connector Ext1,Ext2, PC Input Connector 15Pin, DVI Input Connector, 24Pin

Contents

PDP-TELEVISION Screen Image retention Scart Cable Checking PartsSold Separately Video CableContents Contents SymbolsDepending on your model Actual configuration on your PDP may be differentYour New Plasma Display Panel For further details about connection, refer to pages 52~56 Rear PanelInfrared Remote Control Assembling the Stand-Base Inserting the Batteries in the Remote ControlWall Mount Bracket Plastic Hanger Installing the Display on the Wall Attachment PanelConnecting External Devices to the PDP Connecting Speakers Ferrite Cores Rear of the PDP Connecting to an Aerial or Cable Television NetworkConnecting a Satellite Receiver or Decoder Using a Coaxial cableMains lead is attached to the rear of your PDP Switching On and OffPlacing in Standby Mode To switch your PDP off, press the I / button againDisplay the on-screen menu system Becoming Familiar with the Remote ControlRemote control is used mainly to Change channels and adjust the volumeTo start the search, press the Enter button Plug & Play FeatureChoosing Your Language If you want to reset this featureSee Storing Channels AutomaticallyAuto NT3.58 NT4.43 PAL60 Storing ChannelsManuallyYou wish to identify Auto PAL Secam orChannel mode Skipping unwanted channels Skipping Unwanted ChannelsSorting the Stored Channels Assigning Names to Channels Activating the child lock Activating the Child LockDynamic Standard Movie Custom High Middle Low Custom Displaying InformationChanging the Picture Standard Brightness, Sharpness Adjusting the Picture SettingsCustom Options available in PC, DVI Mode Contrast Result The Custom menu is displayedCustom PC mode only Colour1 Colour2 Colour3 Adjusting the Picture Settings PC or DVI ModeDisplayed again Setting the Picture PC ModeSetting the Picture PC Mode If reception is weak, you can fine tune a channel manually Using the Fine TuneColour System and Sound System settings are correct Freezing the Current Picture Viewing the Channel Scan PictureSelecting the Picture Size Positioning and Sizing the screen using ZoomDNIeTM Digital Natural Image engine Selecting the Film ModeMelody sounds when the television is powered on or off Setting the Blue ScreenSetting the Melody Sound TV Ext.1 Ext.2 AV S-Video Component PC DVI Table of PIP SettingsViewing the Picture In Picture PIP Tvpip Using the LNA Low Noise Amplifier Feature Using the Digital NR Digital Noise Reduction FeatureStandard Music Movie Speech Custom Changing the Sound StandardAdjusting the Volume Automatically Adjusting the Sound SettingsStereo Setting the TruSurround XTSelecting the Internal Mute Selecting the Sound Mode depending on the model Setting the Sleep Timer Setting and Displaying the Current Time Absent Power Off Switching the Television On and Off AutomaticallySatellite STB, AV Receiver, DVD Receiver, Game Viewing an External Signal SourceExt.1 Ext.2 AV S-Video Component PC DVI Redirecting an Input to the External Output Contents Teletext FeaturePress the TTX/MIX button again Displaying the Teletext InformationTo display Press Selecting Display OptionsSelecting a Teletext Input Connecting to the External DevicesInput/Output Specification Rear of the TVConnecting to the S-Video Input Connecting to the PC Input Connecting to the DVI InputConnecting to the Component Input To Display the DVD Home Theater Connecting and Using the Home Theater SystemConnecting the Home Theater System Correct settings for these two variables are Setting up Your PC Software Windows onlyNVidia chipset Input Mode PC/DVIVideo Signal Dot x Line Vertical Horizontal DVI Input Connector Pin ConfigurationsScart Connector Ext1,Ext2 PC Input Connector 15PinNormal picture but no sound Check the volume Power buttonCheck the picture contrast and brightness settings Check the volumeMemo After Sales Service