Samsung SCC-C6407P manual Focus Mode, Dis, Detail

You can select one of four modes for white balance adjustment as follows:

-ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the color temperature is monitored continuously and thereby white balance is set automatically. The following are the approximate supported color temperature ranges in these modes.

ATW1 : 2500K ~ 9300K(✻1)

ATW2 : 2000K ~ 10000K(Mode recommended for sodium lighting)(✻2)

✻1. If the color temperature is out of this range in ATW1 mode, proper white balance may not be obtained. In that case, select ATW2 mode.

✻2. In ATW2 mode, if one color is dominated in the shooted area, the color can be displayed differently.

Therefore, select the mode which is appropriate for the environment.

-AWC(Auto-Tracing White Balance Control): In this mode, accurate white balance is obtained by pressing [ENTER] while having a white paper in front of the camera. White Balance data will be maintained after set it once. AWC mode is best in locations where the color temperature of light source is constant.

-MANU : If WHITE BAL menu is set to MANU mode, the user can set the white Balance considering the current illumination. Select MANU item and press [ENTER], the sub screen where you can select Manual White Balance will be shown. Use the left/right keys to select 3200K, 5600K or OFF(USER) mode in the PRESET menu.

-3200K : Set color temperature to 3200K

-5600K : Set color temperature to 5600K

- USER : Choose out a proper value from the RED and BLUE graph for color and temperature setup.

FOCUS MODE

In the FOCUS MODE MENU, the Focus method can be set to AF, MF, or ONEAF.

- AF	: With AUTO FOCUS MODE, you can monitor the screen continuously
	and it will focus automatically. While moving the zoom keys, it will
	automatically focus so FOCUS key input is not necessary.
- MF	: In MANUAL FOCUS MODE the user adjusts the Focus manually.

-ONEAF : The ONEAF Mode performs Auto-focusing only when the SCC-C6407(P) stops after moving and when the SCC-C6407(P) is not moving it is same as MF mode.

❈When in the MF/ONEAF Mode, press the NEAR and FAR keys on the Controller (SSC-1000) at the same time to perform AUTO FOCUS.)

Use the left/right keys to select AF, MF or ONEAF in the FOCUS MODE menu.

(VIDEO SET)
IRIS	ALC...
SHUTTER	OFF
AGC	OFF
WHITE BAL	ATW1
DIS	OFF
FOCUS MODE	AF
SPECIAL	...
EXIT	QUIT

SPECIAL

In SPECIAL menu, you can directly adjust REVERSE, Y-LEVEL, C-LEVEL, and DETAIL functions.

- REVERSE : Mirrors the screen horizontally, vertically, or in all directions.

E

(VIDEO SET)
IRIS	ALC...
SHUTTER	OFF
AGC	ON
WHITE BAL	MANU...
DIS	ON
FOCUS MODE	AF
SPECIAL	...

➜

Press [Enter]

(AWB/MANUAL)

PRESET 3200K

- Y-LEVEL	: It is used to set the levels for the Sync signal and the entire
	brightness signal of the video signal.
- C-LEVEL	: It is used to set the levels for the Burst signal and the entire colour
	signal of the video signal.
- DETAIL	: Controls both horizontal and vertical distinction.

EXIT QUIT

RET

(VIDEO SET)
IRIS	ALC...
SHUTTER	OFF
AGC	ON

➜

(SPECIAL)

DIS

The DIS(Digital Image Stabilization) function compensates the camera screen shaking incurred from vibration.

WHITE BAL	ATW1
DIS	ON
FOCUS MODE	AF
SPECIAL	...
EXIT	QUIT

Press [Enter]

REVERSE	OFF
Y-LEVEL	(0)I--------
C-LEVEL	(0)I--------
DETAIL	(0)--I-
RET

It is recommended to deactivate the DIS function in the no vibration environment.

EXIT

It's the same as the EXIT function of the CAMERA SET menu.

3-15 3-16