GB
2524

Recording a Programme Immediately

OK
6
R
E
C
M
E
N
U
A
U
D
I
O
S
P
E
E
D
T
V
/
V
C
R
OK
★
5

Protecting a Recorded Cassette

Video cassettes have a safety tab to prevent accidental erasure.
When this tab has been removed, you cannot record on the tape.
1If you wish to protect a cassette, break off the tab using a small
screwdriver.
2To re-record over a protected cassette (safety tab broken), cover
the hole with adhesive tape. 1
NICAM programmes are divided into 3 types. NICAM Stereo,
NICAM Mono and Bilingual (transmission in another language).
NICAM programmes are always accompanied by a standard mono
sound broadcast and you can select the desired sound.
Please refer to page 34.
1Press MENU on the remote control.
Result: The programming menu is displayed.
2Press the corresponding
"
,
❷!
or
➛
,
❿
buttons to select the
FUNZIONI option.
3Press the OK button to select this option.
Result: The FUNZIONI menu is displayed.
4Press the corresponding
"
or
❷
buttons, until the cursor is
placed in front of the NICAM option.
5To... Press
➛
or
❿
, until...
Mono mode NO is displayed.
NO: Only set at this position to record the
standard mono sound during a NICAM
broadcast if the stereo sound is
distorted due to inferior reception
conditions.
NICAM mode SI is displayed.
SI: Normally set at this position.
6On completion, press MENU twice to exit the menu.

NICAM

★

(SV-635X/SV-631X/SV-6315X/SV-613X Only)

O
PTIONS
MENU :SI
DURATA NASTRO :E180
NORMA COLORE :AUTO
IPC :SI
16:9 :AUTO
❿
NICAM :SI
"❷
❿
USCITA:MENU
DISP./
VOL PROG/TRK
U
A
U
D
I
O
DISPLAY
TRK PROG
U
A
U
D
I
O
4
4
4
4
Before recording a programme, you must have preset the corres-
ponding station (unless you are recording via an external video
source). If you have not done so, refer to pages 18 and 19.
1Switch on the television.
2To monitor the programme being recorded, select the television
channel reserved for use with your VCR (or the AV input if used).
3Insert the cassette on which the programme is to be recorded,
with the window visible and the safety tab intact or the opening
covered with adhesive tape.
Result: The VCR is switched on automatically.
4Select:
◆
The station to be recorded using the
PROG/TRK (
"
or
❷
) /
PROG (
"
or
❷
)
buttons
or
◆The AV1, AV2 or AUX
★
(SV-635X/SV-631X/SV-6315X/
SV-6313X/SV-530X/SV-435X/SV-235X only) source using
the INPUT button for a satellite tuner or external video source
Result: The station number is displayed and the programme
can be seen on the television.
★
With SV-635X/SV-631X/SV-6315X-SV-6313X/SV-530X/SV-435X/
SV-431X, you can select the recording speed (SP/LP). Press the
SPEED button.
5Hold REC (
●
) down for a while to start recording.
Result:
The record indicator appears on the television and VCR
display. An index is recorded on the tape (see page 36).
6To stop recording, press
■
once.
➢◆If the cassette is ejected when you start recording,
check that the safety tab is intact or the opening is
covered with adhesive tape.
◆If you reach the end of the tape while recording, the
cassette rewinds automatically.
★(SV-635X)
★(SV-631X/SV-6315X/SV-6313X/
SV-530X/SV-435X/SV-431X/SV-235X/
SV-231X/ SV-2315X/SV-2313X)