MACHINE
WASHING INSTALLATION GUIDE
| Parts supplied |
|
|
| Tools needed |
|
| ||
|
| Type1 | Type2 |
| Tie strap | Tape measure | carpenter’s | Pilers | Flat screwdrilver |
| Wrench | Bolt hole covers | Water supply hoses Hose guide | (option) | level | ||||
1 | PREPARATION. |
|
|
|
|
|
|
| |
1. Check the installation location. □ CHECK : Solidly constructed floor (Not Carpeting and soft tile surfaces) | |||||||||
| 2. And move the washer to the installation location. |
|
|
|
|
| |||
* When installing the washer on a pedestal, do the installation before next step.
2REMOVING ALL SHIPPING BOLTS.
Remove all shipping bolts | Hold the shipping bolt | Fill the holes with the |
at the back of washer with | with your hand and pull it | supplied bolt hole covers. |
supplied spanner. | through the wide section of |
|
| the hole. Repeat for each |
|
| shipping bolt. |
|
CAUTION: Failure to remove the shipping bolts will cause vibration and noise.
3 COLD & HOT WATER HOSES INSTALLATION ON FAUCETS. | HOT COLD | |||
|
| Rubber washer |
|
|
Coupling | Rubber |
|
|
|
| washer |
|
|
|
Make sure a Rubber | Tighten Coupling by hand | Then tighten | Run water in a bowl or | |
washer is inside each | until it is snug. | turn with pliers. | basin to get rid of any debris | |
coupling on both ends. |
|
| inside hose. Check for HOT | |
|
|
|
| and Cold water supply. |
4WATER HOSES INSTALLATION ON WASHER.
COLD (Left) | HOT (Right) | ||||||
Water | Water | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Connect one end of the | Tighten Coupling by hand | Then tighten | For proper operation, make |
COLD/HOT water supply | until it is snug. | turn with pliers. | sure both Hot & Cold hoses |
hoses to the each COLD/ |
|
| from faucets are connected to |
HOT water supply intakes |
|
| the corresponding Hot / Cold |
at the back of the washer. |
|
| water inlets on the washer. |
CAUTION: Make sure that the HOT & COLD hoses are switched with each other.
Installation
|
|
|
|
| French on back |
5 |
|
|
|
| Spanish on back |
CONNECTING THE DRAIN HOSE. |
|
|
| ||
Drain hose | Case 1. Wash basin | Case 2. Laundry tub Hose | Case 3. Stand pipe | ||
| retainer |
| Hose | ||
|
|
|
| 8” Max | retainer |
|
|
|
|
| |
|
|
| 96” Max | 6” Min |
|
|
|
|
|
| |
|
|
| 18” Min |
| 96” Max |
|
|
|
| Tie strap | 18” Min |
|
|
|
|
| |
| Hose guide |
| Tie strap |
|
|
| To keep the drain hose | The drain hose must be | Laundry tub must be no | Do not insert the drain hose | |
| spout bent, use the | placed at a height between | shorter than 18 in (46 cm) | too far into the stand pipe: 6 | |
| supplied plastic hose | 23.6 in (60cm) and 35.4 in | and no longer than 96 in | - 8 inches, and no more. | |
| guide. | (90cm). | (245 cm). |
|
|
6 MOVE THE WASHER TO ITS FINAL LOCATION AND MAKE SURE IT IS LEVELED.
Confirm whether washer is well seated and does not | Your washer must be leveled on all four sides. Use a |
shake. Adjust leveling legs, if necessary. | carpenter’s level on all four corners of your washer to |
| ensure it’s level. |
7LEVEL THE WASHER BY ADJUSTING THE FOUR LEVELING LEGS.
Level the washer by turning the leveling | Check whether washer shakes | When your washer is leveled, |
wheel in or out as required by using the | and level again, if necessary. | tighten the locking nuts using the |
supplied wrench. |
| wrench or |
CAUTION: Your washer must be leveled on all four sides. An unlevel washer may cause vibration.
8 | Final Test : Water leakage , Vibration & Noise |
| |
| |||
1. Powering your washing machine. |
|
| |
| 2. Run a test cycle(Rinse+Spin) with small amount of laundry such as 4~5 Towels. | ||
| (1) Check for any leakage at the hose connections. |
| |
| If water leaks while water is being supplied or drained, check the water connections. (Refer to Step 3,4,5) | ||
| (2) Check for vibration and noise. |
|
|
| If the washer rocks and vibrates excessively, level your washer again. (Refer to Step 6,7) | ||
| Visits by a Service Engineer to explain functions, maintenance or installation is | ||
| not covered by warranty. |
|
|
| INSTALLATION | □ No water leakage | □ No vibration / noise |
| COMPLETION CHECKLIST | ||
| □ Water hose connected properly | □ Washer leveled | |
| □ Washer plugged in, power OK | ||
| □ Drain hose connected properly | □ Shipping bolts removed | |
3:28:58
