Sanyo VSE-2300, VSE-2400 instruction manual Video Coax Connection, Final Assembly

Be sure to securely tighten all fittings to ensure a liquid-tight seal. Failure to do so could allow water to enter the housing and damage the camera and lens.

6.Connect the supply power wires to the left side or the top side of the terminal block provided. Strip no less than 6 mm (0.25-inch) and no more than 8 mm (0.31-inch) of insulation away from the wire. Be sure not to nick the wires.

7.Cut the camera power cord, leaving enough cable to allow connection to the terminal block. Strip no less than 6 mm (0.25-inch) and no more than 8 mm (0.31-inch) of insulation away from the wire. Be sure not to nick the wires. Connect these wires to the left side or the top side of the terminal block.

8.On heater and heater/blower units, make sure the heater and fan wires stay connected to the terminal block.

6.7Video Coax Connection

WARNING: Only use the cables specified under "INSTALLATION, Cable Requirements" for wiring of the video coax connection.

1.For VSE-2300 versions, install a 1/2-inch NPT fitting into the remaining hole in the rear cap. For VSE-2400 versions, install a 3/8-inch NPT fitting through the center small hole of the rear cap.

2.Route the video coax cable through one of the fittings installed in step 1 or one of the feed-through fittings in the base.

3.Attach BNC connector to the coax and connect it to the

camera. Pull any excess wire out of the housing and tighten the fitting to 8.5 N.m to 9.0 N.m (75 in.lb to 80 in.lb). This torque rating is approximately 1 to 1-1/2 turns

past the point where the fitting starts to grip the wire. Failure to do so will result in water damage to all electronic parts.

Be sure to securely tighten all fittings to ensure a liquid-tight seal. Failure to do so could allow water to enter the housing and damage the camera and lens.

Use of "drip loops" is recommended on the wiring outside of the rear end cap.

6.8Lens Wiring

WARNING: Only use the cables specified under "INSTALLATION, Cable Requirements" for wiring of the lens.

1.Install the last 1/2-inch NPT fitting into the remaining hole in the rear cap. Zoom lenses can only be installed into VSE-2400 housings.

2.If installing a zoom lens, insert the lens control cable through the last fitting at the rear of the housing. Attach the lens wiring to the lens mating connector and connect it to the lens. If mating connector is not available, connect

directly to the lens cable. Pull any excess wire out of the housing and tighten the fitting to 8.5 N.m to 9.0 N.m

(75 in.lb to 80 in.lb). This torque rating is approximately 1 to 1-1/2 turns past the point where the fitting starts to grip the wire. Failure to do so will result in water damage to all electronic parts.

NOTE: See specification on lens cord for correct plug connection.

Be sure to securely tighten all fittings to ensure a liquid-tight seal. Failure to do so could allow water to enter the housing and damage the camera and lens.

3.If using a pan/tilt with a feed-through cable, insert the camera/lens function cable in through the left fitting at the rear of the cradle. Wire the functions as described above or as needed.

Use of "drip loops" is recommended on the wiring outside of the rear end cap.

6.9Camera/Lens Adjustment

Verify camera and lens operation before final assembly of the cradle into the housing. Adjust the camera focus and iris as necessary. See individual camera instructions.

6.10 Final Assembly

1.Use the plugs or fittings provided to plug any remaining holes in the rear cap.

2.Reinstall the cover. Align the bottom of the cover ribs with the top of the base. Slide the cover onto the base. Make sure the seal is not folded over or torn. Use silicone grease to lubricate the seals if necessary. See Figure 10.

9