R

Section 4

4.7 HILLSIDE OPERATION

WARNING

DO NOT operate on steep slopes.To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. Under no circumstances should the machine be operated on slopes greater than 15 degrees. ALWAYS FOLLOW OSHA APPROVED OPERATION.

1.This mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Wet grass reduces traction and steering control. The Roll-Over Protection System is standard equipment for this machine. See Section 2.5, page 6 of this manual for further details.

2.To prevent tipping or loss of control, do not start or stop suddenly, avoid unnecessary turns and travel at reduced speed. If tires loose traction, disengage blades and proceed slowly off the slope.

3.Avoid sudden starts when mowing uphill. Sudden starts may cause the machine to tip backwards.

4.Loss of traction may occur when traveling down hill. Weight transfers to the front of the machine and may cause the drive wheels to slip causing loss of braking or steering.

5.Keep tires properly inflated.

4.8 PARKING THE MOWER

1.Park the machine on a flat, level surface only. Do not park the machine on an incline.

2.Place the steering control levers in the neutral position.

3.Disengage the cutter blades.

4.Slow the engine to idle speed.

5.Engage the parking brake.

6.Turn the ignition key to the OFF position and remove the key.

4.9 AFTER OPERATION

1.Wash the entire mower after each use. Do not use high pressure spray or direct the spray onto electrical components.

- IMPORTANT -

Do not wash a hot or running engine. Cold water will damage the engine. Use compressed air to clean the engine if it is hot.

2.Keep the entire mower clean to inhibit serious heat damage to the engine or hydraulic oil circuit.

3.Check the drive belts for proper alignment and any signs of wear. Correct and adjust if necessary.

Danger

To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.

4.After the mower has cooled down, fill the fuel tank with fresh, clean fuel at the end of every day of operation. See Engine Owner's Manual for proper octane requirements.

5.Check the tire pressure. Adjust pressure if necessary.

4.10 REMOVING CLOGGED MATERIAL

Danger

ROTATING BLADES

NEVER PUTYOUR HANDS INTOTHE DISCHARGE CHUTE FOR ANY REASON!

Shut off the engine and remove the key and only then use a stick or similar object to remove material if clogging has occurred.

1.If the discharge chute becomes clogged, shut off the engine and remove the ignition key. Using a stick or similar item, dislodge the clogged material. Then resume normal mowing.

16

Page 19 Page 21
Page 20
Image 20
Scag Power Equipment STC48V26BS manual Hillside Operation, Parking the Mower, After Operation, Removing Clogged Material
Page 19 Page 21

STC61V-25CV-FR, STC48V-26BS, STC48V26BS, STC61V-25CV, STC61V-23BV specifications

Scag Power Equipment has established itself as a leader in the outdoor power equipment industry, and its line of mowers, particularly the STC series, exemplifies premium engineering and cutting-edge technology. Among the standout models are the STC52V-23BV, STC52V-25CV-FR, STC52V-25CV, STC61V-23BV, and STC61V-25CV. Each model is designed to meet the diverse demands of commercial and residential landscaping, providing efficiency, performance, and durability.

The STC52V-23BV and the STC52V-25CV-FR are both equipped with powerful V-twin engines that deliver dependable performance under tough conditions. These engines are designed to provide high torque, enabling users to tackle tougher mowing tasks without sacrificing speed or efficiency. With a cutting deck width of 52 inches, the STC52V models offer excellent maneuverability while providing ample coverage for large lawns.

On the other hand, the STC61V-23BV and STC61V-25CV models feature an impressive 61-inch cutting deck, making them ideal for larger properties. The wider deck allows for more efficient mowing with fewer passes, ultimately saving time and reducing operator fatigue. Both models also boast V-twin engines, ensuring robust performance that can handle dense grass and uneven terrain with ease.

One of the significant characteristics of the STC series is Scag's innovative Velocity Plus cutting deck technology. This unique design enhances airflow beneath the deck, resulting in superior grass cutting and improved discharge. The deck's aerodynamic shape not only ensures a clean cut but also allows for better grass collection in conjunction with optional bagging systems.

Additionally, all STC models are built with operator comfort in mind. Ergonomically designed controls, spacious seating, and intuitive instrument panels enable operators to work efficiently without discomfort during extended periods. These mowers also come standard with heavy-duty frames and high-quality components that offer durability and long-lasting performance, even in the most demanding conditions.

Another noteworthy feature across the STC lineup is the ease of maintenance. Scag Power Equipment has designed these mowers with accessible components, making it easier for users to perform routine maintenance tasks. This focus on practicality ensures that owners can keep their equipment in optimum condition with minimal effort.

In conclusion, the Scag Power Equipment STC52V-23BV, STC52V-25CV-FR, STC52V-25CV, STC61V-23BV, and STC61V-25CV represent the pinnacle of performance, comfort, and durability in the commercial mower sector. With powerful engines, advanced cutting technology, and a focus on user experience, these mowers continue to set the standard for excellence in outdoor power equipment.
Top Page Image Contents