Manuals / Scag Power Equipment / Lawn and Garden / Lawn Mower

Scag Power Equipment STC61V-27CV Rotating Blades, Hillside Operation, Parking the Mower

Models: STC48V-22FS STC52V-24FX STC48V-22FS-LE STC61V-27CV

1 80
Download 80 pages 60.37 Kb
Page 20
Image 20

R

Section 4

4.7 HILLSIDE OPERATION

WARNING

DO NOT operate on steep slopes.To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. Under no circumstances should the machine be operated on slopes greater than 15 degrees. See Figure 2-4, Page 7 to help determine approximate slope of area to be mowed. ALWAYS FOLLOW OSHA APPROVED OPERATION.

1.This mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Wet grass reduces traction and steering control. The Roll-Over Protection System is standard equipment for this machine. See Section 2.5, page 6 of this manual for further details.

2.To prevent tipping or loss of control, do not start or stop suddenly, avoid unnecessary turns and travel at reduced speed. If tires loose traction, disengage blades and proceed slowly off the slope.

3.Avoid sudden starts when mowing uphill. Sudden starts may cause the machine to tip backwards.

4.Loss of traction may occur when traveling down hill. Weight transfers to the front of the machine and may cause the drive wheels to slip causing loss of braking or steering.

5.Keep tires properly inflated.

4.8 PARKING THE MOWER

1.Park the machine on a flat, level surface only. Do not park the machine on an incline.

2.Place the steering control levers in the neutral position.

3.Disengage the cutter blades.

4.Slow the engine to idle speed.

5.Engage the parking brake.

6.Turn the ignition key to the OFF position and remove the key.

4.9 AFTER OPERATION

1.Wash the entire mower after each use. Do not use high pressure spray or direct the spray onto electrical components.

- IMPORTANT -

Do not wash a hot or running engine. Cold water will damage the engine. Use compressed air to clean the engine if it is hot.

2.Keep the entire mower clean to inhibit serious heat damage to the engine or hydraulic oil circuit.

3.Check the drive belts for proper alignment and any signs of wear. Correct and adjust if necessary.

Danger

To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.

4.After the mower has cooled down, fill the fuel tank with fresh, clean fuel at the end of every day of operation. See Engine Owner's Manual for proper octane requirements.

5.Check the tire pressure. Adjust pressure if necessary.

4.10 REMOVING CLOGGED MATERIAL

Danger

ROTATING BLADES

NEVER PUTYOUR HANDS INTOTHE DISCHARGE CHUTE FOR ANY REASON!

Shut off the engine and remove the key and only then use a stick or similar object to remove material if clogging has occurred.

1.If the discharge chute becomes clogged, shut off the engine and remove the ignition key. Using a stick or similar item, dislodge the clogged material. Then resume normal mowing.

16

Page 19 Page 21
Page 20
Image 20
Scag Power Equipment STC61V-27CV, STC48V-22FS Rotating Blades, Hillside Operation, Parking the Mower, After Operation
Page 19 Page 21

STC48V-22FS, STC52V-24FX, STC48V-22FS-LE, STC61V-27CV specifications

Scag Power Equipment has a longstanding reputation for producing high-quality zero-turn mowers, and the models STC61V-27CV, STC48V-22FS-LE, STC52V-24FX, and STC48V-22FS stand out for their exceptional performance, durability, and innovative technologies.

The STC61V-27CV is equipped with a robust 27 HP Kohler engine, providing ample power for cutting through tough grass and elevating efficiency in landscaping tasks. Its 61-inch Velocity Plus cutting deck ensures a superior mowing experience, delivering precise cuts with the ability to handle various turf conditions. This model features a comfortable seat and ergonomic controls, ensuring maximum operator comfort during extended use. Additionally, the cutting height can be easily adjusted from 1 to 5 inches, allowing users to customize their mowing to suit different grass types and preferences.

Meanwhile, the STC48V-22FS-LE boasts a compact design ideal for residential and commercial properties. Powered by a 22 HP Kawasaki engine, this model is equipped with a 48-inch cutting deck, which offers a perfect balance between maneuverability and cutting capacity. The LE package includes luxurious features such as a high-back seat for added comfort and easy access to maintenance points, ensuring that the mower remains in peak condition. The model's easy-to-use controls and responsive steering make it an excellent choice for first-time users.

The STC52V-24FX offers a blend of power and versatility with its 24 HP Kawasaki engine and 52-inch cutting deck. This model is designed for those who require a longer run-time and increased productivity. The mower features an innovative grass catcher option, making it easier to collect clippings for a tidy finish. Furthermore, the heavy-duty frame enhances structural integrity, while the commercial-grade components ensure long-lasting service.

Lastly, the STC48V-22FS enhances user experience with its practical features. Similar to other models, it features a 22 HP Kawasaki engine coupled with a 48-inch cutting deck, tailored for residential lawns and smaller commercial properties. The mower’s compact design and efficient grass discharge system optimize cutting performance while minimizing downtime.

Overall, Scag Power Equipment offers a wide range of high-performance zero-turn mowers. Each model, including the STC61V-27CV, STC48V-22FS-LE, STC52V-24FX, and STC48V-22FS, incorporates advanced technologies and superior engineering to meet the demands of any lawn care professional or dedicated homeowner. With a commitment to innovation and quality, Scag continues to set the standard for excellence in outdoor power equipment.