Manuals / Scag Power Equipment / Lawn and Garden / Lawn Mower

Scag Power Equipment SZC manual Tractor Contd, Cutter Deck, Hydraulic System, Productivity

Models: SZC

1 67

Download 67 pages 4.54 Kb

Page 15

Section 3

3.3 TRACTOR (CONT'D)

Travel Speed:
Forward	0-7.5 MPH
Reverse	0-5 MPH
3.4 CUTTER DECK

-NOTE-

The machine will travel at 7.5 mph for transport purposes. For best cutting performance the forward travel speed should be adjusted depending upon the cutting conditions.

Type:	Floating, Adjustable, Anti-scalping, Hybrid Design Combines
	Out-front and Belly-mount Designs
Construction:	Dual-plate deck construction, top of deck consists of two steel
...................................................................................................	plates 10-gauge and 7 gauge, 7-gauge (3/16") deck skirt.
True Cutting Width:	36" (91.44 cm), 42" (106.68 cm)
Cutting Height Adjustment:	Foot Operated Lever Adjustment from Operator's Seat, 1.50" to
	5.5" in 1/4"increments
Cutter Blades:	197 Thick, Milled Edge, Wear Resistant Marbain™
Blade Engagement:	Electric Blade Engagement Clutch with Control Panel Switch
	Connected to the Cutter Deck via through a Belt.
Discharge Opening:	Extra Wide Discharge Opening with Spring Loaded Discharge
	Chute and Turbo Baffle
Spindles:	Heavy-duty 1-1/8" Top Dimension Spindle Shaft, Cast Housing,
	Taper Roller Bearing, Low Maintenance with Top Access Grease
	Fitting and Grease Overfill Relief Poppet
Spindle Pulleys:	Cast Iron (SZC36A), Split Steel (SZC42A) with Easily Removed
...................................................................................................	Taper Hubs
Cutter Deck Belts:	B-section with Kevlar Cord. Self-adjusting, Self-tightening
SMZC36	Scag Part Numbers - 483001
SMZC42	Scag Part Numbers - 483002
Electric Clutch Type	Ogura Heavy Duty PTO Clutch Brake

3.6 HYDRAULIC SYSTEM

Hydraulic Oil Filter	10 Micron Spin-on Element Type
Hydraulic Reservoir	Cast Aluminum; 2 Quart Capacity

3.7 PRODUCTIVITY

The following chart will aid you in determining how many acres your Scag mower will cut per day.

The chart is an estimate based on 8 hours per day cutting time at 6 MPH with a 20% allowance for overlap and turns.

Cutting Width:	36"	42"
Acres Per Day:	14	16

11

Image 15

Scag Power Equipment SZC manual Tractor Contd, Cutter Deck, Hydraulic System, Productivity, Cutting Width, Acres Per Day

Contents

MODEL SZC OPERATOR’S MANUALFAILURE TO FOLLOW SAFE OPERATING PRACTICES Section 1 - General Information TABLE OF CONTENTSSection 2 - Safety Information SUBJECTTABLE OF CONTENTS CONTD 1.2 DIRECTION REFERENCE GENERAL INFORMATIONUSE ONLY SCAG APPROVED ATTACHMENTS AND ACCESSORIES 1.1 INTRODUCTIONCE Mark ISO SymbolsSYMBOL SYMBOLSlow SYMBOLSYMBOL Fast2.1 INTRODUCTION SAFETY INFORMATION2.2 SIGNAL WORDS Signal Word2.4 OPERATION CONSIDERATIONS 2.3 BEFORE OPERATION CONSIDERATIONS CONTD2.5 ROLL OVER PROTECTION SYSTEM 2.4 OPERATION CONSIDERATIONS CONTDFigure 2-1 Seat Belt Inspection Figure 2-1. SZC With Optional Roll Over Protection System 2.6 MAINTENANCE CONSIDERATIONS & STORAGE2.7 SAFETY AND INSTRUCTIONAL DECALS 2005 SZC Safety Decals481039 482285 482100 482286 482290 482834 482291 483023 3.3 TRACTOR SPECIFICATIONS3.1 ENGINE 3.2 ELECTRICAL3.7 PRODUCTIVITY 3.3 TRACTOR CONTD3.4 CUTTER DECK 3.6 HYDRAULIC SYSTEMFigure 4-1 Controls and Instruments START4.2 SAFETY INTERLOCK SYSTEM 7. Left Steering Control Figure 4-1. Used to8. Right Steering Control Figure 4-1. Used to 4.4 STARTING THE ENGINE 4.5 GROUND TRAVEL AND STEERINGForward Travel Figure 4-3 Cutter Deck Engage Switch Reverse Travel4.6 ENGAGING THE DECK DRIVE CUTTER BLADES 4.7 HILLSIDE OPERATION 4.8 PARKING THE MOWER4.9 AFTER OPERATION 4.12 RECOMMENDATIONS FOR MOWING 4.13 ADJUSTING CUTTING HEIGHT4.10 REMOVING CLOGGED MATERIAL 4.11 MOVING MOWER WITH ENGINE STOPPEDFigure 4-5 Adjusting Cutting Height HEIGHT ADJUSTMENT PEDALFigure 4-4 Deck Release Lever CURE TROUBLESHOOTING CUTTING CONDITIONSCONDITION CAUSECURE TROUBLESHOOTING CONTDCONDITION CAUSECURE Section TROUBLESHOOTING CONTDCONDITION CAUSEFigure 6-2. Brake Rod Adjustment ADJUSTMENTS6.1 PARKING BRAKE ADJUSTMENT Figure 6-1. Brake Adjustment6.2 TRAVEL ADJUSTMENTS Neutral AdjustmentFigure 6-3. Steering Control Rods Adjustment 6.5 BELT ALIGNMENT Tracking Adjustment6.3 THROTTLE CONTROL AND CHOKE ADJUSTMENTS 6.4 BELT ADJUSTMENTCutter Deck Pitch 6.6 CUTTER DECK ADJUSTMENTSFigure 6-4. Cutter Deck Adjustment Cutter Deck LevelFigure 6-6. Cutter Deck Stop Custom-Cut Baffle AdjustmentFigure 6-5. Cutter Deck Height Adjustment Cutter Deck HeightFigure 6-8. 3 Custom-Cut Baffle Position Figure 6-7. Custom-Cut BaffleFigure 6-9. 3-1/2 Custom-Cut Baffle Position Figure 6-10. 4 Custom-Cut Baffle Position7.1 MAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS MAINTENANCEMAINTENANCE CHART - RECOMMENDED SERVICE INTERVALS CONTD 7.2 LUBRICATION - GREASE FITTING LUBRICATION CHART SEE FIGURESuper Lube MEP #2 & Super Stay-M #2 found at Conoco Stations Figure 7.1 Lubrication Fitting Points GREASE FITTING LUBRICATION Lubricant Interval Lithium MP White Grease40 Hours/Weekly Chassis Grease 100 Hours/Bi-monthly Chassis Grease 200 Hours/Monthly Chassis Grease 500 Hours/YearlyFigure 7-3 Hydraulic Oil Filter and Drain Plug 7.3 HYDRAULIC SYSTEM A. Checking Hydraulic Oil LevelB. Changing Hydraulic Oil Figure 7-2 Hydraulic Oil ReservoirC. Changing Engine Oil Filter C. Changing Hydraulic Oil Filter Element7.4 ENGINE OIL A. Checking Engine Crankcase Oil Level B. Changing Engine Crankcase OilFigure 7-6 Engine Fuel Filter Location 7.6 ENGINE AIR CLEANERA. Cleaning and/or Replacing Air Cleaner Element 7.7 BATTERYB. Jump Starting A. Charging the BatteryB. Blade Sharpening C. Blade Replacement7.8 DRIVE BELTS 7.9 CUTTER BLADES A. Blade InspectionFigure 7-10 Blade Replacement 7.10 TIRES7.11 BODY, DECK, AND UPHOLSTERY Section 45 SZC 2005 CD Section 36A”& 42A CUTTER DECKSDescription Section 36A”& 42A CUTTER DECKSPart PartSection CUTTER DECK CONTROLS CUTTER DECKSZC 2005 CDC Description SectionCUTTER DECK CONTROLS PartSZC 2005 SMC Section SHEET METAL COMPONENTSDescription Section SHEET METAL COMPONENTSPart Part2005 SZC ROPS Section SZC ROLL OVER PROTECTION SYSTEM4 04040-13 Flatwasher, 1/2-.562 x 1.375 Ref. Part No. No. Description1 483140 SZC ROPS 2 483150 Seat Belt, ROPS 3 04001-145 Bolt, Hex Head 1/2-13 x 3-1/2”SZC 2005 DSC Section DRIVE SYSTEM COMPONENTSRef. Part No. No. Description Section DRIVE SYSTEM COMPONENTSSZC 2005 EAPKA Section ENGINE AND ATTACHING PARTSDescription SectionENGINE AND ATTACHING PARTS PartTo Pump SZC 2005 SSCSTEERING COMPONENTS Ref. Part No. No. Description Section STEERING COMPONENTSSZC 2005 BSC Section BRAKE COMPONENTS3, 3A 23 221 04001-163 Bolt, Hex Head 1/2-13 x 3-3/4” Ref. Part No. No. DescriptionENGINE Section FUEL AND HYDRAULIC SYSTEMFRAME FRAME TABDescription Section FUEL AND HYDRAULIC SYSTEMRef. Part PartMOUNT Section ELECTRICAL SYSTEMTO STARTER FRAME ENGINEDescription SectionELECTRICAL SYSTEM PartPORT B Section HYDRAULIC PUMP ASSEMBLYPORT A SIDEDescription HYDRAULIC PUMP ASSEMBLYSection PartREVERSE Heavy-DutyCommercial FORWARDPart Description482285 KAWASAKI ADAPTER HARNESS Section ELECTRICAL SCHEMATIC - KAWASAKILIMITED WARRANTY - COMMERCIAL EQUIPMENT