Measurements shown below are in inches | Seagate ST940210AS instruction

Measurements shown below are in inches.

2 .399

COF CONN. DATUM B

C OF DRIVE

( .189 )

2

SATA

( .020 )

SECTION B-B (SATA)

.039 B C D

2 .152

.399

2

DETAIL A (PATA)

B

.039 B C D

.016 C

2 .012

.370

2

DETAIL A (SATA)

1DIMENSIONS PER EIA-720 OR SFF 8201 SPECIFICATION.

2DIMENSIONS PER SFF 8212 OR SFF 8223.

3DRIVE LENGTH W/ PATA IS 3.945±.057 (WORST CASE). DRIVE LENGTH W/ SATA IS 3.957±.062 (WORST CASE).

3.945 ± .010 (BASE)

.157 2

1 2.750 ±.010

(BASE)

PATA			3
BASE			1
			3.567
	.551	1

.374 ±.008

-D-

2X .118 BOTH SIDES

1

BASE	3.567
	(BASE) 1

.551

1

B

DETAIL A

( .490 )

.217 ±.050

.217 ±.050

( .673 )

2X M3 X 0.5-6H

MOUNTING HOLES; BOTH SIDES

.12 MIN FULL THREAD

0.148 ±.010 X 90

1

4X M3 X 0.5-6H

MOUNTING HOLES; BOTH SIDES

.10 MIN FULL THREAD 0.148 ±.010 X 90

1

1

2.430

-B-

.160 1

-C-

Figure 2. Mounting dimensions—top, side and end view

20	LD25 Series 5400.2 Product Manual, Rev. C

Image 26

Seagate ST940210AS, ST980210AS, ST960210AS, ST920210AS manual Measurements shown below are in inches

Contents

LD25 Series Page Contents Seagate Technology support services Interface List of Figures LD25 Series 5400.2 Product Manual, Rev. C Introduction Parallel ATA Pata Serial ATA Sata LD25 Series 5400.2 Product Manual, Rev. C Drive specification ST980210A ST960210A ST940210A Specification summariesSpecification summary for ATA/PATA Parallel ATA models Following web Specifications for Sata Serial ATA models Formatted capacity Default logical geometryLBA mode Cylinders Read/write heads Sectors per track 16,383 Physical characteristics Recording and interface technology Typical seek times msec Read Write Seek timeTime to ready Time to ready Typical Max @ 25C Power specifications Voltage tolerance Typical current profileConducted noise Active mode Power-management modesPower management modes Idle mode Environmental specifications Nonoperating shock ShockOperating shock Vibration Drive level acoustics AcousticsElectromagnetic immunity Electromagnetic immunity Reliability Safety certificationMeasurement type Specification Agency certification FCC verification Korean RRLAustralian C-Tick N176 European Union Restriction of Hazardous Substances RoHS Environmental protectionCorrosive environment LD25 Series 5400.2 Product Manual, Rev. C Handling and static-discharge precautions Mounting the drive Measurements shown below are in inches Breather filter hole precautions Breather filter hole location How to configure the drive How to connect Sata cables How to use the cable-select option How to configure Parallel ATA Pata drivesHow to configure the drive as a master or slave LD25 Series 5400.2 Product Manual, Rev. C Interface Refer to Serial ATA Sata Interface Serial ATA connector pin definitionsSignal Segment Pin Function Definition Pin Function Definition P10 Ground 2nd mate P11 Reserved Connector Cable Signal Name Contact Conductor Pata interface signals and connector pinsConnector signals Cable Connector Conductor Contact Signal Name Supported commands Command name Command code in hex ATA-standard commands ATA-standard security commands Command name Command code in hexATA-standard power-management commands Identify Device command Word Description Value XxxxH Description if bit is set to Bit Word Bit Word Ultra DMA mode 4 is supported Set Features command Set Features command values Code in features register A.R.T. command S.M.A.R.T. commandsM.A.R.T. commands Technical Support InternetPresales Support Data Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index Page TMR LD25 Series 5400.2 Product Manual, Rev. C Page Seagate Technology LLC