Sears 139.53915D owner manual Install Door Control, Connecting Multiple Door controls

INSTALLATION

STEP

6

Install

the

Door

Control

To prevent possible SERIOUSINJURYor DEATHfrom

Locate door control within sight of door, at a minimum

electrocution:

• Besure power is not connected BEFOREinstalling door

height of 5 feet (1.5 m) where small children cannot reach,

control

away from moving parts of door and door hardware.

• Connect ONLYto 24 VOLTlow voltage wires

If installing into drywall, drill 5/32" holes and use the

To prevent possible SERIOUSINJURYor DEATHfrom a closing

anchors provided. For pre-wired installations

(as in new

home construction), it may be mounted to a single gang

garage door:

• Install door control within sight of garage door, out of reach

box (Figure 2).

1 .Strip 7/16" (11 mm) of insulation from one end of bell

of children at a minimum height of 5 feet (1.5 m) and away

from ALL moving parts of door.

wire and connect to the two screw terminals on back of

• NEVERpermit children to operate or play with door control

door control by color: white wire to 2 and white/red wire

push buttons or remote control transmitters

to the 1.

2. Remove cover by gently prying at slot in top of the

• Activatedoor ONLYwhen it can be seen clearly, is properly

adjusted andthere are no obstructions to door travel.

cover with a small flat head screwdriver. Fasten with

• ALWAYSkeepgarage door in sight until completely closed.

6ABx1-1/4" self-tapping screws (drywall installation) or

NEVERpermit anyone to cross path of closing garage door

6-32x1" machine screws (into gang box) as follows:

• Install bottom screw, allowing 1/8" (3 mm) to protrude

Outside

Keylock Accessory

Connections

above wall surface.

To opener quick-connect terminals: white to white;

• Position bottom of door control on screw head and

white/red

to red.

slide down to secure. Adjust screw for snug fit.

• Drill and install top screw with care to avoid cracking

HARDWARE

SHOWN ACTUAL

SIZE

plastic housing. Do not overtighten.

• Insert top tabs and snap on cover.

3. (For

standard

installation

only)

Run bell wire

up wall

Control

Panel

(std

installation)

_'/ _

Insulated

Staples

and across ceiling to motor unit. Use insulated staples

to secure wire in several places. Do not pierce wire with

a staple, creating a short or open circuit.

Control

Panel

(pre

wired)

Drywafl

Anchors

4. Strip 7/16" (11 mm) of insulation from end of bell wire.

Connect bell wire to the quick-connect terminals as

Figure

1

Figure

2

follows: white to white and white/red to red.

REMOVE

& REPLACE COVER

PRE WIRED

NOTE: When

connecting

multiple

door controls

to the

To Replace

iNSTALLATiON

opener, twist same color wires together. Insert wires into

insert

Top

quick-connect holes: white to white and red/white to red.

Tabs

First

5. Position the antenna wire as shown.

6. Use

tacks or staples

to permanently attach

entrapment

24 VoR

warning label to wall near door control, and manual

2 Conductor

Bell Wire in

release/safety

reverse test label in a prominent

location

Gang Box

on inside of garage door.

Quick Connect

NOTE: DO NOT connect power and operate opener at

this time. The trolley will travel to the full open position

Push

Bar

but will not return to the close position until the sensor

beam is connected and properly aligned.

	I1_ _J	Top
		Mounting
		Hole	To release or insert wire.		Door Control
,_.,,,___		_ Terminal
			push in tab with	screwdriver	Connections
/I
	-"1>.Hscrews
Bell	I _"_	J Bottom	tip
			Strip wire 7/16"	Red-
WireI I-- 181 4 Moont ng
_Hole			(11 ram)
			17/16"	(11 mm) I

(BACK VIEW)

White Grey Antenna

17