Sears 153.335815, 153.335961, 153.335941, 153.335803, 153.335915 Troubleshooting Guide contd

Troubleshooting Guide (cont'd)

Operational Conditions

SMELLY WATER

In each glasslined water heater there is installed at least one

anode rod (see parts section) for corrosion protection of the tank. Certain water conditions will cause a reaction between this

rod and the water. The most common complaint associated with

the anode rod is one of a "rotten egg smell". This odor is derived

from hydrogen sulfide gas dissolved in the water. The smell is the result of four factors which must all be present for the odor to develop:

a.a concentration of sulfare in the supply water.

b.little or no dissolved oxygen in the water.

c.a sulfate reducing bacteria within the water heater. (This harmless bacteria is non-toxic to humans.)

d.an excess of active hydrogen in the tank. This is caused by the corrosion protective action of the anode.

Smelly water may be eliminated or reduced in some water heater models by replacing the anode(s) with one of less active material,

and then chlorinating the water heater tank and all hot water

lines. Contact Sears Service for further information concerning

an Anode Replacement Kit #9001453 and this Chlorination Treatment.

If the smelly water persists after the anode replacement and chlo- rination treatment, we can only suggest that continuous chlori-

nation and filtering conditioning equipment be considered to eliminate the water problem.

Do not remove the anode leaving the tank unprotected. By doing so, all warranty on the water heater tank is voided.

"AIR" IN HOT WATER FAUCETS

AWARNING

HYDROGEN GAS: Hydrogen gas can be produced in a hot water system that has not been used for a long period of time

(generally two weeks or more). Hydrogen gas is extremely flammable and explosive. To prevent the possibility of injury under these conditions, we recommend the hot water faucet be opened fur several minutes at the kitchen sink before any electrical applianceswhich are connected to the hot water sys-

I tern are used (such as a dishwasher or washing machine), If hydrogen gas is present, there will probably be an unusual

sound similar to air escapingthrough the pipe as the hot water faucet is opened. There must be no smoking or open flame near the faucet at the time it is open.

HIGH TEMPERATURE SHUT OFF SYSTEM

This water heater is equipped with an automatic gas shut off sys- tem. The high temperature shut off is built into the gas control valve. This system shuts off the gas supply to the water heater

burners when high water temperatures are present. It is non- resettable. If the high temperature shut off activates, the gas con- trol valve must be replaced. If this were to occur, turn "OFF" the

entire gas supply to the water heater. Contact the Sears Service Center.

&WARNING Shouldoverheatingoccur or the gassupplyfail to shut off, urn 'OFF" the manual gascontro valveto the app ante.

NOT ENOUGH OR NO HOT WATER

Check the pilot flame. It may have gone out, All models have

ianheckopeningthe manualbehind gasthe shutouteroffvalvedoor fortoviewingbe sure theit ispilotopen. .

If the piiot is not lit, follow the "Lighting" instructions in this manual or located above the gas control valve on the water heater to relight the pilot. If the water was extremdy hot and is now cold, the high limit safety temperature shut off may have put out the burner and pilot. If the high temperature shut off

activates, the gas controlvalve must be replaced. Contact the Sears Service Center.

The gas control knob must be turned to the "ON" position.

:" The temperature adjustment dial may be set too low. See the Temperature Regulation" section.

The gas company can check the gas input to see if it is correct.

An underfired water heater will not beat water as quicldy.

Look for leaking or open hot water faucets. Make sure all are dosed.

•The cold water inlet temperature may be colder during the win-

ter months. It will take longer to heat the water and seem like less hot water.

•If you cannot find what is wrong, call the Sears Service Center.

WATER IS TOO HOT

1.The temperature adjustment dial may be set too high. See the "Temperature Adjustment" section.

NOTE: A period of time is necessary after an adjustment has been made for the water temperature to reach the new tem- perature setting.

2.If lower temperature settings will not lower the water tempera- ture, call the Sears Service Center.

&WARNING

Due to the nature of the typical gas water heater, the water temperature in certain situations may he hotter than the thermostat setting.

Short, frequent draws of hot water - especiallywith very cold incoming water - can shockthe thermostat into brief

operation resulting in hotter and hotter layers of water closerto the top of the tank.

Changes in hot water usagepatterns or raising the tem- perature differential between the cut-on of the thermo- stat and the cold water temperature will usuallyeliminate the problem.

29