Sears 200.71232 owner manual Charging your battery outside the vehicle

8.For automatic charging, touch AUTO then a charge-rate pad 2, 20, or 60 Amps. The charging will stop when the battery is fully charged.

9.For manual charging, touch a charge rate pad then select a charge time up to 18 hours. If more than 135 minutes of charging time is needed, reset the time when the original time runs out. Refer to the Time Chart in the “Setting the Controls” on page 8 of “Using your Battery Charger.”

10.In the MANUAL mode, at the 60-Amp charging rate, the METER will show a charge rate of 25 to 30 amps or less when the battery is at or near full charge. At the 20-Amp charging rate, the METER will show a charge rate of 8 to 10 amps or less when the battery is at or near full charge.

At the 2-Amp charging rate, the METER will show a charge rate of .75 to 1 amp when the battery is at or near full charge.

11.TO AVOID OVERCHARGING in the Manual mode, monitor the METER frequently.

12.When the battery is fully charged, turn the POWER switch to the OFF position and unplug the charger power cord.

13.Standing away from the battery, remove the charger clamps in this order: (1) from the chassis connection and, (2) from the battery post or terminal.

14.Clean and store the battery charger in a dry location.

Charging your battery outside the vehicle:

1.Remove the battery from vehicle, making sure to disconnect grounded terminal first with all accessories and lights turned off in the vehicle.

2.Check the polarity of the battery posts as indi- cated on the battery case: POSITIVE (POS, P, +) and NEGATIVE (NEG, N, -).

NOTE: On top-post batteries, the positive battery terminal usually has a larger diameter post than the negative one.

3.Connect the red (POSITIVE) charger clamp to the POSITIVE post of the battery. Be sure to rock the clip back and forth to make a solid connection.

4.Attach a 6-gauge (AWG) or a 4-gauge (SAE) insulated battery cable of at least 24-inches in length to the NEGATIVE battery post. This cable will provide a safer connection because arcing and sparking will occur away from the battery. (The battery cable is not provided with the charger, but may be purchased at most automotive accessory outlets.)

5.Standing as far away from the battery as possible, connect the black (NEGATIVE) lead of the charger to the free end of the cable. Rock the clamp to make a solid connection. IMPORTANT: Wear safety glasses and face away from the battery while making this final connection.

6.Make sure the POWER switch is set to the OFF position. Next plug the power cord into a grounded AC outlet.

7.For automatic charging, touch AUTO then a charge-rate pad. The charger will quit when the battery is fully charged.

8.For manual charging touch a charge rate pad then select a charge time, from up to 18 hours. If more than 135 minutes of charging time is needed, reset the time when the original time runs out. Refer to the time chart in the “Setting the Controls” on page 8 of “Using Your Battery Charger.”

9.In the MANUAL mode at the 60-Amp charging rate, the METER will show a charge rate of 25 to 30 amps or less when the battery is at or near full charge. At the 20-Amp charging rate, the METER will show a charge rate of 8 to 10 amps or less when the battery is at or near full charge. At the 2- Amp charging rate, the METER will show a charge rate of .75 to 1 amp when the battery is at or near full charge.

10.TO AVOID OVERCHARGING in the Manual Mode, monitor the METER frequently.

11.When the battery is fully charged, turn the POWER switch to the OFF position and unplug the charger power cord.

12.Standing away from the battery, remove the charger leads. Remove the grounded clamp first, then the one on the battery.

13.Clean and store the battery charger in a dry location.

10