ASSEMBLY

CUTTING LINE HEAD

CONFIGURATION

Brush and Saw Blade ConflguraUonsfollow this section.

& WARNING:

THE LINE LIMITER IS SHARP AND CAN CUT YOU. BE SURE TO WEAR GLOVES WHILE WORKING WITH THE LINE UMITER.

INSTALLING THE PLASTIC LINE TRIMMER SHIELD (See Fig. 5 )

Place the plastic line trimmershieldon the gearbox, and align the four screw holes as illustmfed.

Place the shield support plate under the shield and align the four screw holes.

Secure the plasticline trimmershieldusing the 4 mount- ing screws provided in the loose parts bag.

Tighten evenly (70 Ib-in mimimum) using the hex key

 

THE PLASTIC UNE TRIMMER SHIELD

provided in the

loose parts bag.

 

 

MUST BE PROPERLY

INSTALLED FOR ALL

Arbor

_ -F_

 

 

 

LINE TRIMMER USAGE. THE PLASTIC

 

 

 

 

 

UNE TRIMMER SHIELD PROVIDES PAR-

 

 

 

 

 

TIAL PROTECTION FROM THE RISK OF

 

 

 

 

 

THROWN OBJECTS TO THE OPERATOR

Driyin_] /t!/i_

_J_

Plast_Une

 

AND OTHERS,

 

 

 

 

 

 

PI.:ASTIC_?,__;-.....Di 2! .

/

T,mme,.

INSTALLING

UNE :LIMI3_R_-ONTO

 

 

 

 

 

 

 

 

 

Shield

LINE TRIMMER SHIELD

(See Fig.4)

Shield Support

__,,

_.

 

 

 

 

 

 

 

Plate

 

 

 

Pos_on line limiteronto the plastic line trimmershield.

 

Figure

5

 

IMPORTANT:

ALTHOUGH SCREW HOLES EXIST ON

INSTALLING

THE DUAL

MNE

HEAD

BOTH EDGES OF THE PLASTIC LINE TRIMMER

(See Fig. 6 & 7 )

 

 

SHIELD, MAKE SURE YOU INSTALL THE LINE UMo

 

 

 

 

rrER ON THE SIDE SHOWN

IN THE ILLUSTRATION.

Before installing the dual line head, make sure the driving

• Secure line limiter to the plastic line trimmershield using

diskis in place on the gear box,

 

Rotate the hex fastener on the dual line head counter-

the two mounting screws, lock washers, and nuts found

clockwise onto the arbor shaft.

 

in the loose parts bag using a phillips screwdriver and

 

•Tum the arbor shaftto align one of the three holes in the

8ram wrench.

 

 

 

 

Tighten securely.

 

 

 

ddving diskw_ththe hole in the gearbox.

 

 

 

Insert the locking pin through the gearbox and driving

 

 

 

 

 

 

 

Nuts_

Une Umiter .

disk. This will lock the driving disk, and prevent the arbor

 

shaft from turning while you tighten the dual line head.

 

 

 

 

 

 

 

--,-,,,,. . /_'___,_,

Line Limiter parts are

While holdingthe Iockingpinin place, tighten the dual line

 

head onto the arbor shaft counterclockwise using the

'

,,,=_,,_'"::_':rs

 

located in a bag at-

 

blade nut/spark plug wrench(15-20 Ib-ft);

 

 

"///'_

 

tashed

to the Plastic

Should the arbor shaft continue to turnwhile you are tight-

 

 

._--

_l

Line Trimmer Shield.

 

 

ening the dualline head, re-positionthe/ockingpinthrough., ,,..

 

 

 

 

 

 

 

 

 

 

 

 

the gearbox and driving disk.

 

 

Plastic Line _

\y_-_-

 

Screws

 

Locking Pin

Arbor Shaft

 

 

 

 

 

FdmmerShield

 

 

 

 

......Plastic Line

 

 

 

 

 

Figure 4

 

 

 

 

 

 

 

 

 

Trimmer Shield

 

Disk

PRE-INSTALLATION

If the metal blade shield is installed on the unit, you must first remove the-nut,supportflange, blade, and metalb/ade shield as follows before installing the plastic fine trimmer shieldand duat line cutdng head.

Clip blade transport/storage cover over the blade. (Refer to figure 9)

To remove blade (Sea Figures 11 or 14), place lockingpin through the gearbox and driving disk to preventthe arbor shaft from turning and remove the blade nut by turning clockwise with blade nut/spark plug wrench. Save parts removed for future use.

Remove 4 screws with hex key holding the metal blade shield. Save these 4 screws for installationofthe plastic line trimmer shield.

Dual

Hex Fastener

 

(underneath)

Figure

6

Lockin! Pir_ual

Cutting Head

Plastic Line

 

Trimmer Shield _'<

II Counterclockwis_

Blade Nut/Sl_ irk Plug Remove Clockwis_ Wrench

Figure 7

-8-

Page 8
Image 8
Sears 358.79828 Cutting Line Head Configuration, Installing UNE LIMI3R-ONTO, Line Trimmer Shield, Installing Dual MNE Head