.Assemble one 1/2" x 4" hex bolt, one 1/2" hex nut and one 7/16" standard washer into top of slotted hole in channel assembly. Assem- ble one 7/16" standard washer and one 7/16" hex nut on bottom of 1/2" bolt under channel

assembly. See figure 6. DO NOT TIGHTEN AT

THIS TIME.

. Assemble channel assembly to hitch plates at front of tractor as shown in figures 6 and 7.

FRONT VIEW

HITCH PLATES

1/2 x 4"

HEX BOLT

1/2'" HEX

PIVOT

\\

7/16" WASHERS

ASS'Y.

FIGURE 6

. Assemble keeper plates over each end of pivot shaft with lip under hitch plates (see figure 7) and secure with two 1/8" (large) hairpin

cotters through small holes near each end of shaft.

HITCH PLATE, (R.H.)

HITCH PLATE, (L.H.)

ENGINE

PULLEY,,,,

 

BOLT

1/8"

 

CLEARANCE

1/2"" HEX NUT

CHANNEL ASS'Y, FRAME MEMBER

FIGURE 8

5.Assemble blade assembly to channel assembly

by aligning holes in pivot plate with holes in

reinforcement plate and inserting pivot shaft. See figure 9. Secure by assembling two 1/8"

x1-1/4" cotter pins into small holes near ends t)f pivot shaft. Spread ends to retain.

NOTE

Blade shoes are factory assembled to blade assembly in lower setting. See adjustments step "'C'"page 10 for repositioning.

(TOP) 5/16"' HEX NUT

PLASTIC

CAP

BLADE ADJUST

SPRING5/16"" HEX NUT

BLADE

(BOTTOM)

PIVOT &FT

1/8"" HAIRPIN

COTTER

SHOE

CHANNEL

ASS'Y.

SPRING PIVOT

3HT HAND

BRACKET

118" x 1-1"/4'"

KEEPER PLATE

FIGURE 7

MOUNT ROD SHAFT

FIGURE 9

COTTER PIN

. Adjust 1/2" x 4" stop bolt, previously assembled into channel assembly (step 1). See figure 8. Adjust hex nuts, above and below

channel to provide approximately 1/8" clearance between channel and the tractor engine pulley with the stop bolt positioned against frame member. See figure 8.

NOTE

The stop bolt must be tightened in

place

before

blade

assembly to channel.

. To assemble blade adjust spring, remove plastic

cap, 5/16" flat washer and one 5/16" hex nut. Adjust the remaining 5/16" hex nut on the long bolt to approximately one inch down from end of bolt threads. Assemble adjusting bolt through hole in top edge of blade and hold in place with 5/16" flat washer and 5/16" hex nut removed earlier. Do not tighten 5/16" hex nut at this time. Push down on the spring and hook end of spring over spring mount rod as shown in figure 9. Tighten 5/16" hex nut on top edge of blade

down against the bottom 5/16" hex nut. Replace plastic cap over end of adjusting bolt threads. See figure 9,

Page 5
Image 5
Sears 486.244062 owner manual This Time, Front View Hitch Plates HEX Bolt, Assy, Hitch PLATE, L.H, Clearance

486.244062 specifications

The Sears 486.244062 is a notable entry in the realm of consumer electronics, specifically in the category of personal computers. Launched during a time when PCs were becoming increasingly integral to both home and business environments, this model featured a blend of cutting-edge technologies and user-friendly characteristics that appealed to a wide range of customers.

At the heart of the Sears 486.244062 was its Intel 80486 microprocessor, which represented significant advancement over its predecessors. Operating at a speed of 33 MHz, this processor provided enhanced performance for multitasking capabilities, enabling users to run various applications simultaneously without significant lag. This was particularly valuable during the early 1990s when software applications began to demand more processing power.

The computer typically came equipped with 8 MB of RAM, expandable up to 32 MB, accommodating the increasing demands of modern operating systems and applications of the time. This validated the 486's suitability for both business and home use, ranging from simple document editing to more detailed graphic design tasks.

In terms of storage, the Sears 486.244062 incorporated a 520 MB hard drive, which was ample for the period. It allowed users to store numerous files, applications, and multimedia content, marking a departure from the limited storage capacities of earlier models. The inclusion of a 3.5-inch floppy disk drive further enhanced its functionality, offering a convenient medium for data transfer and backups.

The system also featured a VGA-compatible graphics card, which enabled it to deliver clear and vibrant visuals, enhancing the user experience, particularly in gaming and graphic applications. Coupled with high-fidelity sound capabilities, the Sears 486.244062 catered to an audience interested in multimedia entertainment.

User comfort was also prioritized in the design of this model. It often featured an ergonomic keyboard layout and a mouse that was precise and responsive, creating a comfortable environment for extended use.

In conclusion, the Sears 486.244062 emerged as a reliable computer option during a transformative period in technology. With its robust performance, expandable hardware capabilities, and focus on user experience, it carved a niche that appealed to both professionals and casual users, leaving a lasting impact on personal computing trends of the era.