Sears 53DS900078, 53DS900077 installation instructions Installation Instructions

Installation Instructions

GENERAL

These instructions cover the installation of the accessory wall

mounting kit. The kit is provided for mounting cooling only,

multi-split, and heat pump units to a wall due to space limitations.

IMPORTANT:	Read these installation			instructions			thoroughly
BEFORE starting	installation.
Refer to Table 1 for kit contents and usage.
Table	I--KIT	CONTENTS		AND USAGE
MOUNTING
KIT PART		USAGE			KIT CONTENTS*
NUMBER
				2	-	Long Bracket
						Section
				2	-	Horizontal	Bracket
	All 018,024		Sizes			Section
53DS900077	Plus			2	-	Angled Bracket
	38HDF/538E-		F 030			Section
	38QRF/638Q-		F030	6	- Wall Lag Bolts
				6	- Lag Bolt Washers
				6	- Wall Lag Bolt
						Shields (Anchors)
				4	-	Mounting	Feet
						Bolts (1 in.)
				4	-	Mounting	Feet
						Locknuts
53DS900078	AIIElse			10 -		Bracket	Assy.
	030 -	060				Locknuts
				10 -		Bracket	Assy.
						Bolts (1/2 in.)
				10 -		Bracket	Assy.
						Lockwashers

*The contents for both kits are the same: however, the items are different sizes for specific applications.

SAFETY CONSIDERATIONS

Installation of this equipment can be hazardous due to system

pressures, electrical components and equipment location. Only

trained, qualified installers and service technicians should install.

start up and service this equipment. Observe all applicable precautions.

Improper installation, adjustment, alteration, service,

maintenance, or use can cause explosion, fire. electrical shock, or

other conditions which may cause personal injury or property

damage. Consult a qualified installer, service agency, or your

distributor or branch for information or assistance. The qualified

installer or agency must use factory-authorized kits or accessories

when modifying this product. Refer to the individual instructions packaged with kits or accessories when installing.

Follow all safety codes. Wear safety glasses and work gloves. Use

quenching cloth for brazing operations. Have fire extinguisher

available. Read these instructions thoroughly and follow all

warnings or cautions attached to the unit. Consult local building

codes and National Electrical Code (NEC) for special requirements.

Recognize safety information. This is the safety-alert symbol

Z_. When you see this symbol on the unit and in instruction manuals, be alert to the potential for personal injury.

Understand the signal words DANGER, WARNING,

CAUTION, and NOTE. These words are used with the

safety-alert symbol. DANGER identifies the most serious

hazards which will result in severe personal injury or death.

WARNING signifies hazards which could result in personal

injury or death. CAUTION is used to identify unsafe practices

which may result in minor personal injury or product and

property damage. NOTE is used to highlight suggestions which

will result in enhanced installation, reliability, or operation.

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury or death.

Before installation, always check to be sure main power to system is OFE

INSTALLATION

1.Unpack accessory from carton. Check to be sure contents are not damaged or missing. See Table 1.

2.Select mounting location on the wall. The location must

allow for use of wall studs for mounting security. Check

local building codes and building construction to ensure that there is adequate wall strength to support the mounted

unit. The location must also allow for condensate drainage

from the unit. Be sure this drainage does not cause a problem for the area beneath the unit.

IMPORTANT: Ensure that the unit will be mounted at least 6 in. from the wall for proper airflow. Also ensure that there will be at least 6 in. of airflow clearance on the coil end and 18 in. on the

compressor end for service access.

IMPORTANT: Do not drill new holes in the bracket assembly in order to move the unit closer to the wall.

3.Use the enclosed long bracket sections as a template for

marking the mounting kit location on the wall. Both long bracket sections must line up with the middle and coil end

mounting feet of the unit. See Fig. 1.