Sebo Airbelt D owner manual USE and Maintenance of Brushes & Heads

Retracting the Cord - Figure 13

To retract the cord, switch the vacuum off, unplug it from the outlet, then press the cord rewind button (#7, figure 13) and the mechanism will automatically rewind the cord. You must hold the button down until the cord is fully rewound. Hold plug while rewinding into the cord wheel. Do not allow the plug to whip while rewinding. The rewind mechanism will stop automatically when you release the button. Before rewinding the cable, always switch off and unplug the vac- uum.

7

Figure 13

LED Suction-Power Indicator - Figure 14
Your AIRBELT D4 canster features an LED light display (8) that monitors suction power. It is
located around the ON/OFF power control knob (6). When the canister power is switched on, a			8
blue light will blink right and left. As the suction increases, the lights will rotate around the
ring. The faster the rotation, the higher the suction.
Storing the Vacuum - Figures 15, 16 & 17				Figure 14
The vacuum can be stored with the canister in a horizontal or				20
vertical position. The standard Parquet brush has a parking tab	45		26
located on the back of the neck. The optional Premium Parquet,
Kombi and Turbo nozzles have a parking tab located on the front
of the neck (45). Insert the parking tab into the upper side of the
parking groove and slide down firmly. For vertical storage or for
easy carrying, use the parking slot on the underside (26). For
horizontal storage, use the parking slot on the end of the canis-
ter (21).
	Figure 15	Figure 16		Figure 17

USE AND MAINTENANCE OF BRUSHES & HEADS

!	Always unplug vacuum from outlet before dismantling any part of machine!
	To remove a brush or power head, switch off the power and unplug the vacuum.
	Then, press the tool release button (9) and pull the tube out.

NOTE! D4 users with ET-1, ET-2 or DISCO power heads, please refer to your power head user’s manual for more detailed instructions for operating and maintaining your power head.

Parquet Brush (standard) - Figure 18

The D4 comes with a parquet brush (28) that was designed specifically for vacuuming hard floors. It is lightweight with soft bristles, so it glides gently over floors and provides easy maneuverability. Fibers and hair can be pulled out of the bristles manually, or vacuum the bristles with the telescop- ic tube.

Premium Parquet Nozzle (optional) - Figure 19

The Premium Parquet nozzle (32) is especially designed for use on hard surfaces. The brush should be cleaned regularly. Remove the parquet nozzle from the telescopic tube to clean. Fibers and hair can be pulled out of the bristles manually, or vacuum the bristles with the telescopic tube. The brush strips are removable for cleaning and replacement.

Kombi Nozzle (optional) - Figure 20

The Kombi nozzle (10) is adjustable for carpet or hard floors. To set for carpet, slide the up arrow button (46) to the right until it clicks into place. The hard floor dusting brush will raise up allowing the head to move over the carpet. To set for hard floors, slide the down arrow button (47) to the left until it clicks into place. The brush will lower to gently sweep your floors. The slider in Figure 20 is set in the position for hard floors. Remove the Kombi nozzle from the telescopic tube to clean. Fibers and hair can be pulled out of the bristles manually, or vacuum the bristles with the telescop- ic tube. The brush strip is removable for cleaning and replacement.

28

Figure 18

32

Figure 19

46

		10
▲	▲	47
Figure 20
48		33
▲	▲

Turbo Nozzle (optional) - Figure 21 Figure 21

The Turbo nozzle (33) has an air-driven rotating brush for gentle brushing of carpets. The Turbo nozzle can be adjusted for high and low pile carpet. To adjust the head for high pile carpet, push the slider button (48) to the right. For low pile carpet, push the slider button (48) to the left. The slider in Figure 21 is set in the low pile position. Remove the Turbo nozzle from the telescopic tube to clean. Remove fibers and hair from the brush manually.

10