Sebo K2, K3 owner manual Identification Of Parts, Assembly, Standard Attachments

IDENTIFICATION OF PARTS

1.	Handle grip	14.	Exhaust filter cover
2.	Power control slider (K3 only)	15.	AIRBELT shock absorber
3.	Handle release button	16.	Carrying handle
4.	Telescopic tube	17.	Suction opening
5.	Slide button	18.	Hose release button (K3 only)
6.	Power cable	19.	Hose neck
7.	Tool release button	20.	Crevice nozzle
8.	Combination nozzle	21.	Parking attachment holder
9.	On/Off power control knob	22.	Power cable shroud
10. Warning light		23.	AIRBELT clip
11. Upholstery Nozzle		24.	Parking attachment holder
12. Mains cable (K3 only)		25.	Filter bag cover release catch
13. Hose		26.	Filter bag cover

27					Standard Attachments
	20		20. Crevice nozzle			27. Dusting brush clip
28	11		11. Upholstery nozzle			28. Dusting brush
				Brushes, Heads, Optional Attachments
				29. Premium Parquet nozzle - standard for the
	29			31	K3 Volcano, Red and Onyx. Optional for the
		30			K2 Midnight Blue - Part #7200DG
				30.	Combination nozzle - standard for the
32					K2 Midnight Blue. Optional for the K3
	33			34	Volcano, Red & Onyx and K2 Hunter
					Green - Part #7260DG
				31.	Turbo nozzle - standard for the K2 Hunter
	35b				Green. Optional for the K3 Volcano, Red &
			36		Onyx and K2 Midnight Blue Part #6780ER
35a
				32.	Radiator brush - Part #1496HG
				33.	Straight tube (20 in.) - Part #1084HG
				34.	AIRBELT - Available in several colors
					and patterns - Part #6047AM/01-08

1 2

	12
3		13
4
5		10
6	9	11
7		14

8

15 16 171819

20 21 22 24 25

15 23 26

Power Heads - optional for the K3: 35a. ET-1 Power head - Red: Part #9299AM; Orange: Part #9272AM; Onyx: Part #9951AM

35b. ET-2 Power head - Red: Part #9250AM 36. ET-H Power head - Red: Part #9257AM

ASSEMBLY

Push the neck (19) of the hose (13) into the suction opening of the canister (17). K3: The notch in the		K3
suction opening will line up with the raised bar on the neck. When the notches are lined up correct-
ly, the neck will snap firmly into place. To release the hose from the suction opening, press the
release tab (18) on the neck of the hose (19), and pull the neck out. K2: To release the hose from	K2
the suction opening, squeeze the tabs (37) on the retaining ring and pull the neck out.			19
Attach the short mains cable (12 - K3 only) on the underside of the handle by connecting one
		19	17 18
cable plug where the hose connects to the handle and the other where the handle connects to
the telescopic tube.		37 17
Connect the handle (1) to the top of the telescopic tube (4). Snap in place. To release the telescop-
ic tube (4) from the handle, push the handle release button (3) and slide the handle out.			1
Attach the head or brush to the bottom of the telescopic tube (4). Insert the bottom of the telescopic
tube into the neck of the head or brush (38) until it locks into place; or line up the square hole in the		3	4
telescopic tube with the notches in the front of the neck, and snap firmly into place. To release a head
or brush from the telescopic tube (4), push the release button (7), and pull the head or brush tool off
the end of the telescopic tool. The release button (7) is in the same position on all of the heads, brush-		4
es and power heads.
To attach the dusting brush clip (27), locate the two raised ridges on the upper end of the telescopic		7	38
tube (4) just below the handle. Push the clip onto the tube directly below the ridges then slide the clip
up until it locks onto the ridges. Snap the dusting brush (28) into the holder.
NOTE: To attach a SEBO power head (ET-H, ET-1 or ET-2) to your K3 canister, please refer to your
power head owner’s manual for instructions. Attaching incorrectly could cause damage.			7
NOTE: All illustrations shown in this manual represent the K3 model except where part numbers and instructions are different for each model.