SECO-LARM USA E-941SA-80 Installation Manual, MOUNTING THE E-941SA-80Q, Standard Mounting

E-941SA-80Installation Manual

E-941SA-80Installation Manual

MOUNTING THE E-941SA-80Q

A. Drill holes for the mounting plate and
armature plate (see fig. 1 and 2) by
doing the following:
1.	Fold the mounting template along
	the dotted line
2.	Close the door. Find a mounting
	location on the door frame near the
	upper free-moving corner of the
	door, as close to the corner of the
	door frame as possible.
3.	Place the template against the door
	and frame.

the door while the electromagnet is engaged.

3.Do not tighten the armature plate against the door. The plate must be able to pivot around the armature screw.

C. Screw the mounting plate to the door
frame:
1.	Remove the L-shaped mounting
	plate from the magnet.
2.	Insert the provided two 1/8" x 1"
	(4 x 25.4 mm) screws into the

FIG.1 Standard Mounting

	L-shaped
	Maounting
	bracket
Sexnut
bolt	Magnet
	Armature Plate
	Steel and Rubber washers

4.	Drill two holes in the door frame for
	the mounting plate and three holes
	in the door as indicated on
	template.
5.	Only from the sexnut bolt side of the
	door, enlarge the 5mm hole to
	9mm.
B. Mount the armature plate to the door
using the two steel and one rubber
washer (fig. 2):
NOTE — Actual installation varies
according to door style.
1.	Secure the two guidepins into the
	two side holes of the armature

plate.

L-shaped mounting plate and

screw it to the door frame. The

armature plate and the mounting

plate must be concentric or align

with each other.

D. Drill the power cable access hole.

E. Mount the electromagnet to the door

frame (fig. 1) — Use the Allen wrench

to screw the socket-head mounting

screws through the bottom of the

electromagnet into the mounting

bracket.

F. Connect the power leads (fig. 3):

1. Run two power leads from the

power supply through the power

FIG. 2 Types of armature plate mounting

	Steel and		Steel and
	Rubber washers		Rubber
	(as needed)		washers
	Armature		(as
			needed)
Sexnut	Armature	Sexnut
	Screw	bolt
bolt			Armature
			Screw
This side drill	Drill a 5mm	Drill 9mm	Armature
9mm only	hole thru door		Drill a 5mm
		(23/64")
			hole thru door

HOLLOW METAL DOOR	SOLID CORE DOOR
Drill an 5mm hole thru door. From sexnut	Drill an 5mm hole thru door. From sexnut
bolt side only, enlarge the 5mm hole to	bolt side of door, drill 9mm (23/64") hole,
9mm.	25mm in depth.

Steel and Rubber washers (as needed)

Armature Screw

Armature

Tap M5 x 0.8 Thread

REINFORCED DOOR

Drill a 3.5mm dia. hole and tap for M5 x 0.8 thread.

2.Insert the armature screw into the armature plate, then put the rubber washer between two steel washers, and place them over the armature screw between the armature plate and the door. This will allow the armature plate to pivot slightly around the armature screw in order to compensate for door misalignment.

2.Insert the sexnut bolt into the 9mm hole, then tighten the sexnut bolt and the armature screw, just enough so the armature plate can withstand the force of someone attempting to break down

cable access hole into the

electromagnet.

2. Connect the power leads to the red

and black power input wires of the

unit. Observe correct polarity, red

for positive and black for negative.

G. Test the unit.

FIG. 3 Wiring diagram

Power wires to
electromagnet	Control
Red	Device
	+ 12~24VDC
Black	- Power
	Supply

Page 2 SECO-LARM U.S.A., Inc. Page 3