SECO-LARM USA EVT-PC4KQ installation manual port PCI Passive Video Balun Hub, What It Is, Pair

ENFORCER PASSIVE PCI VIDEO BALUN HUB

Installation Manual

Specifications:

EVT-PC4-VT2Q (Video Balun Card)

Range*	B/W: 2,000 feet (610M)
	Color: 1,300 feet (400M)
Video Format	RS170, NTSC, PAL, SECAM, CCIR
Maximum Input	1vpp
Insertion Loss	< 2dB per pair from DC ~ 5 Mhz
Return Loss	>-15dB from DC ~ 5 Mhz
Frequency Response	DC ~ 5 Mhz
Attenuation	DC ~ 5 Mhz, 1.5 dB max
Common Mode Rejection	60 dB, 15 KHz~5 MHz
Impedance
Coax, Male BNC	75 Ohms @ 1 MHz
Terminal Block	100 Ohms @ 1 MHz
Power	No power required
Temperature Range	14o~165oF (-10o~74oC)
Humidity Range	0 ~ 95%
Wire Type	UTP ( 16 - 24 AWG)
Wire Category	CAT2 or better, CAT5 ideal
UTP Connection	Screwless Terminal Blocks
No. of channel	4

*Note: Shorter range may result when baluns are used with DVR.

EVT-PC4P-JTQ (Power Card)

Video Input	Removable terminal block
Power Input	Power jack (2.1mm jack)
Power Output	Removable terminal block
Power Indicator	3-color LED
Voltage output	12VDC (inc. power adapter)
Total Supply Current	4 Amp. (inc. power adaptor)
Temperature Range	14o~165oF (-10o~74oC)
Humidity Range	0 ~ 95%
Wire Type	UTP ( 16 - 24 AWG)
Wire Category	CAT2 or better, CAT5 ideal

ENFORCER®

EVT-PC4-VT2Q	EVT-PC4-VT2Q
4-port PCI Passive Video Balun Hub
Range: Up to 2,000’ (610mm)
EVT-PC4P-JTQ
4-port PCI Power Distributor Card
Range: See chart on page 4.
EVT-PC4KQ	EVT-PC4P-JTQ

4-port PCI Video Balun Hub & Power Card Set (Includes 4 Amp 12VDC Adapter)

WHAT IT IS

The ENFORCER EVT-PC4-VT2Q is a 4-port PCI Video Balun Hub specifically designed for PC based DVR cards . The EVT-PC4-VT2Q is the most practical and cost efficient way of connecting video signals from CCTV cameras to PC based DVR cards via Cat5 cables. It eliminates the need to install individual video baluns on the DVR card side, and is

Minimum Distance Over UTP @ 12VDC*

Current Draw	1 Pair	2 Pair	3 Pair
100mA	100’	200’	300’
300mA	30’	60’	100’
1 Amp	N/A	15’	30’

*Note: Maximum distance depends on voltage, current, ambient temperature, and wire guage. (Maximize distance with 3 UTP pairs.)

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.

This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship.

The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.

Copyright © 2007 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of SECO-LARM.

SECO-LARM®U.S.A., Inc.	FILE: D\DTP\MANUAL\MiEVT-PC4_series_07A.pmd
	Order Part # 764-027%
16842 Millikan Avenue, Irvine, CA 92606	Website: www.seco-larm.com
	PITSW1
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326	E-mail: sales@seco-larm.com

equipped with a gold plated BNC connector for optimum video performance and a screwless terminal block for convenient and organized wiring installations.

The EVT-PC4P-JTQ is an add-on power card for EVT-PC4-VT2Q. When installed with EVT-PC4-VT2Q it will allow power to be transmitted from the PC side to CCTV camera side over the same UTP cables used by the video signal. It centralizes the power suppy of CCTV cameras.

Installation

Installing the EVT-PC4-VT2Q and EVT-PC4P-JTQ

1.Shut down the computer, disconnect the power and remove the computer cover from its chasis. See Fig. 2.

2.Determine the location of the available card slots at the back panel of the computer, and remove the metal covering of the desired slot.

3.Securely mount the EVT-PC4-VT2Q and/or EVT-PC4P-JTQ in their respective slots with the provided screw at the back panel of the computer. Please note that the EVT-PC4-VT2Q and EVT-PC4P-JTQ boards do not need to be inserted into the PCI (Peripheral Componet Interconnect) slots of the computer motherboard. Then replace the cover of the computer.

NOTE: For convenient wiring it is recommended that the DVR cards, EVT-PC4-VT2Q and EVT-PC4P-JTQ, be installed adjacent to each other as shown on Fig. 2.

EVT-PC4-VT2Q Wiring (see Fig. 3) - Video Balun Card

1.Make sure the maximum distance between the CCTV camera and the DVR card does not exceed 1,950 feet for monochrome or 1,300 feet for color.

2.Run the UTP cable from the DVR card to where it will be connected to the CCTV camera. Follow the CCTV camera’s wiring instructions for information on how to safely run and hide this wire.

NOTE: 1. Individual separate passive video baluns such as SECO-LARM’s EVT-PB1 are required for each camera on the camera side.

2.The video baluns are polarity-sensitive. Take note of the colors of the positive & negative wires of the video signal cables as this will be needed when connecting the other end of the UTP cables at the DVR card side.

3.Use the orange/ orange-white color wire pair of the UTP cable for the video signal. Connect the UTP cables to the passive video baluns on the camera side and plug the video baluns into the BNC connector of the CCTV cameras. The EVT-PC4-VT2Q can accomodate a maximum of 4 cameras.