Seiko Group IP-6600

2-3

Section 2 Basic Operations

Set the ID switch on the rear of the printer.

- The ID number must not be unique in the SCSI chain. (Initial

setting: 4)

SCSI connector

NOTE

-Use a dedicated SCSI cable (68-68-pin, 6 m).

If using a cable except the specified one, the printer can

not satisfy FCC and CE regulations.

ID switch

Set the ID number with a small normal

driver, etc. (Initial ID value: 4)

Connect a SCSI cable to a SCSI connector on the rear of

the printer.

(It can be connected to any one of two SCSI connectors.)

Connecting with Computer

NOTE

Contents

Main Page Introduction Page i Deliverables ii Accessories iii Options Consumables Safety Precautions CAUTION v vi CAUTION vii viii Handling Precautions Power Supply Printer Regular Inspection and Maintenance ix Consumables Manual Legend (Notational rules) Page xii Example 3: LCD's state transitions and key operations in the text CONTENTS-1 TABLE OF CONTENTS Section 1 Getting Started (Basic knowledge) 1-1 CONTENTS-2 Section 2 Basic Operations 2-1 CONTENTS-3 Section 3 Operation Panel Menu Operations 3-1 CONTENTS-4 Section 4 Heater Controller Operation 4-1 Section 5 Troubleshooting 5-1 Appendix A-1 1-1 Section 1 Getting Started (Basic knowledge) 1-2 Operating Conditions Installation Space Page 1-4 Consumables 1-6 1-7 1-8 Ink Use our recommended ink cartridges listed below. Page Page Page Page 1-13 External Views, Part Names, and Functions Front 1-14 RearRear Page 1-16 Operation Panel 1-17 External Views, Part Names, and Functions Functions of LCD, LEDs and keys (1) (2) 1-18 Heater Control Panel Functions of LCD, LEDs and keys Page 1-20 LCD Messages and Printer State Messages on the LCD 1-21 (3) Online state (print mode) display The printer is printing. (4) Online state (print pause mode) display The printer is paused. 1-22 (5) Online state (print information mode) display Paper total count and ink removing amount are displayed. 1-23 (7) Shutdown state display The printer is shutting down. (6) Offline (menu mode) display Menus can be operated in offline mode. F/W Version Checking Method Added Functions in V2.00 Here, the function added in V2.00 as a firmware version checking method is described. F/W Version Checking Method X.XX is the F/W version. Section 2 Basic Operations 2-1 Contents of this section Connecting with Computer Page Page 2-5 Turning the Power On/Off Page 2-7 Page Page Page Replacing the Paper Roll Page Page Page 2-15 Select either paper roll or cut sheet. Select a paper type. Page Page Page Page Page Page Page 2-23 Description is made in a case of black color. 2-24 Change During Online Printing Head print position adjustment : 97.00% to 103.00% Press the or key (Note: Disabled at the first scan and last scan) Page Page Page Page Page Page Replacing Ink Cartridges Page Page Page 2-35 Replacing Cartridges during Printing <If the Ink Cover is Opened> 2-36 <If the Ink in Main Cartridge is Used Up> Page Replacing the Waste Ink Bottle Page Page Page Page Page Page Page Page 2-47 Select a paper type again. Select *Yes or No of back feed operation. Installing Paper on Winder Page Page 2-51 2-52 2-53 Changing Heater Control Setting Temperature 2-54 2-55 2-56 Using the Media Pressure Alternation Lever Using the Head Up/Down Lever Page Using the Media Edge Guard 2-60 Using the FAN Guard Slide Lever 2-61 Using the Print Pause/Restart and Cancel Keys 2-62 Inspection & Maintenance Regular inspection and maintenance by operators are described below. 2-63 <Wiper Blade Cleaning> 2-64 <Wiper Sponge Cleaning> 2-65 <Capping Unit Cleaning> 2-66 <Waste Ink Bottle Disposal> <Test Print> <Soft Head Cleaning> 2-67 2-68 2-69 <Head Wash> 2-70 <Ink Charge After Head Washing> Page Page Page 3-1 Section 3 Operation Panel Menu Operations 3-2 Basic Menu Operation Menu Hierarchical Structure (1) Menu Tree (2) (3) 3-3 (4) 3-4 (3) (5) (1) (2) (6) (4) 3-5 (7) 3-6 (5) (6) (7) 3-7 3-8 Basic Operations and Keys 3-9 Operation Procedure for Choice Input, Value Input, Execution, and Character Input 3-10 3-11 3-12 3-13 An example of NAME of the ENTRY menu is given below. Then, modify the value. Select NAME. Modify the value by pressing the or key. (See Character List in the next page. ) 3-14 (6) Press key to determine the parameter. <Character List> ( + key) 3-15 Menu Operations INK Menu 3-16 PAPER Menu 3-17 ENTRY Menu 3-18 3-19 3-20 3-21 3-22 3-23 3-24 3-25 3-26 3-27 3-28 3-29 3-30 The following explains how to copy the parameter registered to paper No. 13 to paper No. 20. 3-31 3-32 Initial values for the registered papers 3-33 3-34 3-35 F.ADJ Menu 3-36 3-37 3-38 SERVICE Menu 3-39 3-40 3-41 CLEANING Menu Page 3-43 3-44 ADJUST Menu 3-45 3-46 3-47 SYSTEM Menu 3-48 3-49 3-50 Page Section 4 Heater Controller Operation 4-2 Temperature Control 4-3 4-4 LCD Display 4-5 4-6 Parameter Setup Mode Note: # will be blinked. This mode is used when the operator sets the heater control system parameters. (1) Setup items and parameters The setup items and parameters are listed in the table below. 4-7 4-8 Page 4-10 Error Messages 4-11 5-1 Section 5 Troubleshooting 5-2 Troubleshooting Before deciding that there is a serious problem with the printer, check the following items. Items to be checked Page 5-4 When an Error Message Appears Service Call Errors 5-5 Page 5-7 Operator Call Errors The following errors can be corrected by the operator. 5-8 5-9 - Error LED is blinking 5-10 When the Printer Fails to Work Correctly 5-12 When a Print Error Occurs Measures to solve print quality problems when a print error occurs Page Appendix A-2 Basic Specifications Printer Specifications Basic printer specifications Options/Consumables A-4 Consumables A-5 Appendix Celsius and Fahrenheit Conversion List