Shark UV219CS owner manual Operating Instructions

Fig. 2

Fig. 1

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Assembling Your Vacuum Cleaner

Note: Do not plug the power cord into an electrical outlet until the vacuum is fully assembled.

Handle Assembly

1.Carefully unpack all components, set aside packaging.

2.Lift vacuum body to upright position.

3. Remove the screws (2) that come attached

to the body.

4.From the rear of the vacuum, align the handle with groove and slide onto vacuum. If necessary, use thumb and finger pressure to slide handle into position.

5.Once handle is in place, secure the handle with the screws (2). (Fig. 1)

Caution: Do not over tighten. Over tightening could strip the screw holes. Do not operate the vacuum without the handle screws in place.

Cord Assembly

1.Make sure that the quick release cord holder is in the upright position.

2. Remove the wire tie from the power cord.

Using the Attachments

1.Place vacuum in its upright position. Make sure that the vacuum cleaner is NOT plugged into the electrical outlet when adding or removing accessories.

2.Turn the carpet adjustment knob to the highest position.

3.Remove the hose connector from the rear of the unit and push in the desired attachment firmly onto the end of the hose.

4.If additional length is required, attach one or both of the extension tubes to the end of the hose and then attach the crevice tool or upholstery brush to the end of the extension tube.

Warning: Avoid tipping the vacuum or setting it on furniture, fringed area rugs or carpeted stairs while you are using the hose with the attachments. When the vacuum is turned on, the beater brush will continue to rotate. Avoid leaving the vacuum in one place for an extended period of time, particularly on thick carpet. Caution: Do NOT pull the vacuum cleaner around the room by the hose as it could tip over and cause damage. When using the attachments, do NOT over extend the hose length when reaching. Trying to reach beyond the hose reach could cause the vacuum to tip over.

How to Start

The upright vacuum can be used on multiple types of carpeting, bare floors or upholstery with attachments. When using the attachment tools such as the crevice tool and the upholstery brush, place the handle of the vacuum in the upright position.

1. Turn the quick release cord holder

14.Insert the right side of the agitator in first by placing the end cap down into the slot and then do the same with the left side. Press firmly to make sure that each end is completely inserted.

15.Check to make sure that the belt is centered on the pulley and that the agitator turns.

16.Replace the top cover over the power head base and replace the screws, first the ones on the back of the power head and then the ones on the bottom and screw firmly.

Changing the Headlight Bulbs

Warning: To reduce the risk of electric shock, the power cord must be disconnected before removing the dust cup, HEPA filter,changing the filters or performing maintenance/trouble shooting checks.

1.Turn unit “Off” and unplug from wall outlet.

2.With a Phillips #2 screw driver, remove the two screws that are on the head light lens. (Fig. 23)

3.Lift off the head light lens.

4.Remove the light bulbs by pulling them out carefully.

5.Replace the new bulbs by pushing them in.

6.Replace the head light lens and then replace the two screws on the head light lens to secure in place.

Motor Thermostat

Important: This unit is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur:

•Push the On/Off button once.

•Disconnect the plug from the power source.

•Check the source of overheating problem. (i.e. clogged hose or filter)

•If clogged hose or filter is found, unclog the hose and replace the filters.

•Wait at least 45 minutes before attempting to reuse the vacuum.

•After unit has cooled down for

45 minutes, plug in the cleaner and push the On/Off button. The vacuum should start again.

•If the vacuum still does not start, contact customer service at 1-800-798-7398.

3.Wrap the cord into place by wrapping it in a clockwise direction around the quick release cord holder and the lower cord holder. (Fig. 2)

4.Turn the quick release cord holder to the left or to the

right to unwrap the power cord. (Fig. 2)

Warning: Do not plug in if the power On/Off button is in the "On" position.

4

	to either side 180° to release the
2.	power cord.
	Plug the power cord into the electrical
3.	outlet.
	Depress on the handle release pedal
4.	to release the handle.
	Push the On/Off button to the "On"
5.	position to turn the vacuum on.
	When using the attachments, the
	vacuum must be in the upright
	position. (Fig. 3)

Fig. 3

Fig. 23

9