Shark V1510 owner manual Cleaning & Changing the Hepa Dust Cup Filter, Motor Thermostat

Debris

Screen

Wash once a month or when suction appears reduced.

.

Warning: Allow 24 hours for drying before replacing in unit.

Fig. A

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Cleaning & Changing the HEPA Dust Cup Filter

WARNING: Always unplug the unit from electrical outlet before opening the Dust Cup (container).

IMPORTANT: Do NOT use the HEPA filter cartridge without the debris screen in place.

WARNING: After each Use - Always remove the filter debris screen from the HEPA dust cup filter, then vigorously “TapClean” HEPA filter until no more dust can be removed.

IMPORTANT, Please Note : The “TapClean” HEPA dust cup filter & debris screen will stop most of the tiniest dust particles and airborne allergens from re- entering the air you breathe. Because of this incredible filtration performance, the HEPA dust cup filter will quickly accumulate, inside the white filter folds, many fine dust particles that are difficult to see but which will eventually block or reduce your suction power - if not cleaned properly. Clean the HEPA filter and debris screen after each use as described in this section.

1.To remove the dust cup (container), hold the unit in the upright position to prevent the dust from falling out of the dust cup. (Fig. 6)

Fig. 6

2.To open the dust cup (container), push button and remove the dust cup (container ). (fig. 7)

Dust cup release button

Fig.7

3.Rotate the lower dust cup clockwise to separate it from the filter chamber. Empty and clean the dust cup. (Fig. 8)

Fig.8

FilterDust

Chamber Cup

4.Remove the HEPA filter from the filter chamber. (Fig. 9)

Filter

HEPA Chamber

Filter

Fig. 9

5.Separate the debris screen from the HEPA filter cartridge by grasping the debris screen with one hand and the filter frame with the other and pull apart. (Fig. 10)

6.Vigorously “TapClean” the HEPA dust cup filter on a hard surface until no more dust is observed falling out from between the pleats of the filter. (Fig. 11)

Fig. 11

7.“TapClean” the debris screen or rinse under a faucet until clean.

(Fig. 12) Remember that the debris screen

must be completely	Fig. 12
dry before reinstalling
in the vacuum.
	Debris
	Screen

8.Replace the debris screen on the HEPA dust cup filter and reinstall filter assembly in the vacuum. (Not shown)

PLEASE NOTE: The white pleated filter material in the HEPA dust cup filter will discolor over time -This is NORMAL and will NOT affect the performance of the filter. If the HEPA dust cup filter

is properly "TapCleaned” after each use and suction does not return to 100%, then we suggest that the HEPA filter be “TapCleaned” vigorously until no

more dust can be removed, then rinsed under the faucet and allowed to dry for 24 hours before refitting into the vacuum. (Fig. A) This should be done once a month or when suction appears reduced.

Motor Thermostat

IMPORTANT: This unit is equipped with a motor protective thermostat. If for some reason the vacuum cleaner should overheat, the thermostat will automatically turn the unit off. Should this occur:

•Push the On/Off button once.

•Disconnect the plug from the power source.

•Check the source of overheating problem. (i.e. clogged hose or filter)

•If clogged hose or filter is found, unclog the hose and replace the filters.

•Wait at least 45 minutes before attempting to reuse the vacuum.

•After unit has cooled down for

45 minutes, plug in the cleaner and push the On/Off button. The vacuum should start again.

•If the vacuum still does not start, contact customer service at

1 (800) 798-7398.

HEPA

Filter

Fig. 10

5

CAUTION: The suction hole must be open and free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.

6