Removing and Installing the Lamp Unit, Lamp unit | Sharp PG-D2510X

Removing and Installing the Lamp Unit

Warning!

•Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.

Optional	Lamp unit
accessory	AN-D350LP
	AN-D350LP

Info

•Do not touch the glass surface of the lamp unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

•Do not loosen other screws except for the lamp unit cover and lamp unit.

1 Press STANDBY/ON on the projector or STANDBY on the remote control to put the projector into Standby mode.

2 Disconnect the power cord.

•Unplug the power cord from the AC socket.

•Leave the lamp until it has fully cooled down (about 1 hour).

3Remove the lamp unit cover.

•Close the lens shutter and turn the

projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).

STANDBY/ON button

AC socket

User service screw (for lamp unit cover)

Appendix

57

Image 59

Sharp PG-D2510X Removing and Installing the Lamp Unit, Remove the lamp unit cover, Lamp unit, STANDBY/ON button AC socket

Contents

PG-D2510X Model No Serial No Void the users authority to operate this equipment See bottom of projector Information Product Disposal For Future Reference Maintenance Troubleshooting Index Contents Reference Adjusting the Projector Function PRJ-ADJ1/2 Menu Power-Cord Protection CleaningPower Sources Accessories Overloading Damage Requiring ServiceReplacement Parts Safety Check Do not block the exhaust and intake vents Avoid locations with extremes of temperatureRest your eyes occasionally Other connected equipment Using the projector in other countriesTemperature monitor function Page Optional accessories Accessories Front View Part Names and Functions Rear View Terminals CLICK/EFFECT button 34 VOL +/- Volume buttonsBreak Timer button Picture Mode button Usable Range Remote control signal transmittersInserting the Batteries Easy Start Setup and Projection Turn the computer on Turn the power off Standard Setup Front Projection Setting Up the ProjectorSetting Up the Projector Screen Lens center Signal Input Normal ModeSignal Input 169 Mode Screen Size and Projection Distance Ceiling-Mount Setup Projection PRJ Mode Terminals on the Projector Connecting the Projector to Other Equipment Connecting the Projector to Other Equipment RGB Controlling the Projector by a Computer Connecting the Power CordAC socket Power cord To AC outlet supplied Turning the Projector On Power indicator Lamp indicatorTurning the Projector On/Off Image Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Press Enter to exit the Setup Guide screen Make small adjustments Height Adjust lever Adjusting the HeightAdjusting the Picture Size Use the rear adjustment foot to make the projector level Press Keystone Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Correcting Trapezoidal Distortion Input buttons AV Mute button VOL +/- Volume buttons Buttons Switching the Input ModeAdjusting the Volume Press Resize Resize Mode About Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot Function Displaying an Enlarged Portion of an Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving Image When right-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When left-clicking Picture menu Menu Items Main menu Projector adjustment PRJ-ADJ1/2 menu Example Using the Menu ScreenMenu Selections Quick Start Menu Press Menu Following items can be conﬁgured on the Quick Start Menu Example Adjusting BrightQuick Start Menu Menu Selections Complete Menu Image while watching it To adjust the projected Menu operation n Picture Adjustment Picture MenuSelecting the Picture Mode Adjusting Hue, Saturation, or Value Adjusting the ImageAdjusting the Color Temperature Adjusting the Colors Reducing Image Noise DNR Selecting the Film ModeEco+Quiet Resolution Setting Signal Adjustment SIG-ADJ MenuSignal Type Setting When reproducing Ntsc signals in PAL video equipment Setting the Video Setup Keystone Correction Adjusting the Projected Image SCR-ADJ MenuSetting the Resize Mode Adjusting the Image Position For Americas only Setting the OverscanSetting the On-screen Display Closed Caption Selecting the Wall Color Selecting the Setup GuideSelecting the Background Image Reversing/Inverting Projected Images Auto Restart Function Auto Sync Auto Sync AdjustmentAuto Power Off Function Speaker Setting Enter the same keycode in Re- conﬁrm Adjusting the Projector Function PRJ-ADJ1/2 MenuFan Mode Setting System Lock Function Select On, then press Enter Keylock FunctionSelecting the Quick Start Menu COMPUTER2 Select Checking the Lamp Life Status Setting the Function Button OperationStandby Mode Standby Audio Out Cleaning the projector Maintenance About the temperature warning indicator Maintenance Indicators Abnormally high Are high Lower than 95F +35ºC Replacing the Lamp Regarding the LampLamp STANDBY/ON button AC socket Removing and Installing the Lamp UnitRemove the lamp unit cover Lamp unit Resetting the Lamp Timer COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Connecting Pin Assignments USB Terminal Type B USB connector Basic format RS-232C Speciﬁcations and CommandsComputer control Communication conditions Projector Commands ERR Video Video Input Picture Mode Standard OK or ERR Appendix CC1 Computer Compatibility Chart 21-24 Troubleshooting 53, 54 For Sharp Assistance Speciﬁcations Dimensions Index Kensington Security Standard connector ·················13