Controlling the Monitor with a PC (RS-232C)

You can control this monitor from a PC via RS-232C (COM port) on the PC.

You can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 13), you can make input mode selection/adjustment or can check the status of a specific monitor.

Caution

To control the monitor via RS-232C, set RS-232C/LAN

SELECT to RS-232C.

You cannot use RS-232C and LAN control simultaneously.

PC connection

nOne-to-one connection with a PC

Connect with RS-232 straight cable between the PC’s COM port (RS-232C connector) and the RS-232C input terminal on the monitor.

RS-232C input terminal

PC

To COM port

RS-232 straight cable (commercially available)

nDaisy chain connection… Advanced operation

Connect with RS-232 straight cable between the PC’s COM port (RS-232C connector) and the RS-232C input terminal on the first monitor.

Next, connect RS-232 straight cable to the first monitor’s RS‑232C output terminal and to the second monitor’s RS-232C input terminal. Connect in the same way to the third and subsequent monitors.

Up to 25 monitors can be connected. (Depending on the length of the cable used and the surrounding environment.)

First monitor

 

Second monitor

RS-232C input terminal

RS-232C output terminal

Communication conditions

Set the RS-232C communication settings on the PC to match the monitor’s communication settings as follows:

Baud rate

9600 bps

 

Stop bit

1 bit

 

 

 

 

 

Data length

8 bits

 

Flow control

None

 

 

 

 

 

Parity bit

None

 

 

 

 

 

 

 

 

Communication procedure

nCommand format

When a command is sent from the PC to the monitor, the monitor operates according to the received command and sends a response message to the PC.

 

 

 

 

 

 

 

 

 

 

Return code

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C1

 

C2

C3

 

C4

 

P1

P2

P3

P4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Command field

 

 

 

Parameter field

 

 

(4 prescribed

 

 

(4 character string comprised of:

alphanumerical characters)

 

0-9, +, -, space, ?)

Example: VOLM0030

VOLM 30

*Be sure to input 4 characters for the parameter. Pad with spaces (“ ”) if necessary.

(“ ” is a return code (0DH, 0AH or 0DH)) Wrong : VOLM30

Right : VOLM

30

When inputting a negative value, specify a numerical value in three digits.

Example: AUTR-009

Do not use spaces for MPOS, DATE, and SC01 through SC08. Specify parameters using a specified number of characters.

Example: MPOS010097

If a command has “R” listed for “DIRECTION” in the “RS-232C command table” on page 16, the current value can be returned by using “?” as the parameter.

Example:

VOLM ? ? ? ?

 

From PC to monitor (How much

 

 

 

 

is current volume setting?).

30

 

 

From monitor to PC (Current

 

 

 

 

volume setting: 30).

* If an ID number (see page 13) has been assigned

(For example, ID number = 1).

VOLM

?

From PC to monitor.

30

001

 

From monitor to PC.

PC

To COM port

RS-232 straight cables

(commercially available)

 

E12

Page 12
Image 12
Sharp PN-S655 Controlling the Monitor with a PC RS-232C, PC connection, Communication conditions, Communication procedure