![](/images/new-backgrounds/1125782/1257829x1.webp)
Basic Operation
When performing operation of multiple monitors with the remote control unit, first set the remote control unit to the appropriate remote control mode (see page 7).
2. MUTE
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the previous level.
2
5
7
1
3
4
If using the monitor buttons, either hold both | and | at the |
same time or select MUTE AUDIO from the OPTION menu.
3. MENU
Displays and turns off the menu screen (see page 8).
4. VOL +/- (Volume adjustment)
Pressing or
displays the VOLUME menu when the menu screen is not displayed.
V O L U M E | 15 |
6
8
TIPS
•You can perform operation of the monitor with the rear buttons. Utilize the buttons belonging to the monitor that you would like to operate.
•Operation by using the buttons on the rear side of the product will perform the same functions.
Rear side buttons
Remote control ![](/images/new-backgrounds/1125782/1257829xi6.webp)
![](/images/new-backgrounds/1125782/1257829xi7.webp)
![](/images/new-backgrounds/1125782/1257829xi8.webp)
![](/images/new-backgrounds/1125782/1257829xi9.webp)
unit buttons ![](/images/new-backgrounds/1125782/1257829xi11.webp)
This manual assumes that this product will be used with the remote control unit buttons, except where specifically noted.
1. INPUT (Input mode selection)
The menu is displayed. Press or
to select the input
mode, and press to enter.
Input mode | Video | Audio | |
PC | PC | Audio input terminal | |
PC HDMI | PC/AV HDMI input terminal*1 | *2 | |
AV HDMI | PC/AV HDMI input terminal*1 | ||
|
When the PN-ZB02 (optional) is attached
Input mode | Video | Audio |
PC | PC/AV |
|
PC HDMI | PC/AV HDMI input terminal*1 |
|
PC | PC |
|
PC RGB | PC RGB input terminals*4 |
|
AV | PC/AV | *2 |
AV HDMI | PC/AV HDMI input terminal*1 |
|
AV COMPONENT | AV COMPONENT input terminals*4 |
|
AV | AV |
|
AV VIDEO | AV video input terminal |
|
*1 Select the terminal to be used in HDMI of INPUT SELECT. (See page 11.)
*2 Select the terminal for AUDIO SELECT which is used for audio input. (See page 11.)
*3 Select the terminal to be used in DVI of INPUT SELECT. (See page 11.)
*4 Select the terminal to be used in BNC of INPUT SELECT.
Press or
to adjust the volume of the sound.
*If you do not press any buttons for about 4 seconds, the VOLUME menu automatically disappears.
5. BRIGHT +/- (Backlight adjustment)
Pressing or
displays the BRIGHT menu when the menu screen is not displayed.
B R I G H T | 15 |
Press or
to adjust the brightness.
*If you do not press any buttons for about 4 seconds, the BRIGHT menu automatically disappears.
*When BRIGHTNESS SENSOR is ON or ON: DISPLAY, when the brightness is adjusted BRIGHTNESS SENSOR will become OFF.
6.SIZE (Screen size selection) The menu is displayed.
Press or
to select the screen size. (See page 6.) If using the monitor buttons, select SIZE from the OPTION menu.
7. DISPLAY
Displays monitor information. When you press this button again, the display disappears.
When the
•The display disappears automatically after about 15 seconds.
•LAN is displayed during LAN communication.
•If LAN is displayed in red, there is a duplicate IP address.
If using the monitor buttons, press under INFORMATION in the OPTION menu.
8. MODE (Color mode selection)
Each time you press this button, the color mode changes in the following order:
STD (Standard) → VIVID → sRGB → STD...
• sRGB applies to PC input only.
sRGB is international standard of color representation specified by IEC (International Electrotechnical Commission). Color conversion is made in taking account of liquid crystal’s characteristics and represents color tone close to its original image.
(See page 11.)
If using the monitor buttons, select COLOR MODE from the PICTURE menu.
5 E